How to Pick Out Replacement Pistons for Trailer Disc Brake Calipers

Question

Question:

Looking for pistons for a mission trailer S Series

asked by: Jimmy

0

Expert Reply:

I attached a link to a page that has all of the replacement pistons we have for the disc brake kits we have like the part # BP18-065 which is for 10 and 12k Dexter disc brake kits.

Check out the link and select your axle capacity and brand from the filters and the correct pistons will be listed.

expert reply by: Jameson C

0

Answer 1

The Dexter 12K oil bath axles can be changed over to grease without any issues. The oil does keep the bearings lubricated well, but there is a much higher risk of leaking which leads to a much higher risk of failure. I'd personally move to grease…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

Hey Dale, both DeeMax and Hydrastar make really nice disc brake components. Either kit is going to work really well for your 2022 Grand Design Reflection 337RLS. If you want the best of the best and don't mind paying for the premium brand then go…

view full answer...

Answer 11

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 12

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

How to Pick Out Replacement Pistons for Trailer Disc Brake Calipers

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching