Does Trailer Hub part # AKIHUB-440-2-2K Replace Hub that has Bearing Numbers L44649
Published 12/08/2017
Question:
It's a straight, not tapered spindle. So the bearings should be the same
asked by: Ben L
0
Expert Reply:
I'd have to know the inner bearing number as well or the bearing surface dimension of the spindle. It could be either another L44649 or possibly a L68149 which has different dimensions.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Trailer Hubs and Drums
- Idler Hub
- Pre-Greased
- Standard
- L44649 / L44649
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Continue Researching
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Trailer Hub - AKIHUB-440-2-EZ-2K
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Video: All About the Trailer Idler Hub Assembly for 2,000-lb Axles
- Video: The Low-Down on the Trailer Idler Hub Assembly for 2,000-lb Axles
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Galvanized
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Replacement U-Bolt Axle Mounting Hardware Kit - 3" Axles
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Loadstar ST175/80D13 Bias Trailer Tire with 13" White Wheel - 4 on 4 - Load Range C
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Q&A: What Does BTR and BT8 Mean when Picking Out Replacement Trailer Hub
- Q&A: Replacement Hub Assembly for Older Boat Trailer with 4 Bolt Pattern
- Q&A: How Much Grease is Needed in an EZ Lube Axle
- Q&A: Replacement Trailer Hub for the TDE 46205 with Galvanized Finish
- Q&A: Can I Swap Out The 4 Lug Rims On My Pop Up Camper For 5 Lug Rims?
- Article: Slipper Spring Trailer Suspension System Review
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: The Best 5th Wheel Hitches
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: How to Measure Your Trailer Wheel Bolt Pattern
Ben L.
12/8/2017
It's a straight, not tapered spindle. So the bearings should be the same