Brake Flange Nut Recommendation for Securing Brakes to Timbren Axle Less 3,500 lb Kit

Question

Question:

What nuts do I need to fasten my trailer brake to this suspension? What threads are on the brake flange?

asked by: Garrett

0

Expert Reply:

The size of nut required to secure a brake assembly to the mounting flange of the Timbren Axle Less kit part # ASR35HDS02 is a 3/8 inch, fine thread bolt like # 38N.

expert reply by: Jameson C

0

Answer 1

Jordan, I believe the "main" bolts you're referring to is a 5/8" bolt which you can use 15/16" socket. The Timbren Axle-Less Trailer Suspension #TASR35HDS07 also has 9/16" grade 8 fasteners, which you can use a…

view full answer...

Answer 2

We do have an axle-less system that will provide your 2022 Rockwood Mini Lite with additional clearance. The Timbren Axle-Less Trailer Suspension System is what you need. Based on what I have found, you have 3,500 lb axles on your travel trailer. I…

view full answer...

Answer 3

This is a great question. You generally want to allow 3" clearance between the top of the tire and the fender (or bunk), at minimum, when your trailer is fully loaded. This should give you adequate clearance for potholes and bumps. In order to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Brake Flange Nut Recommendation for Securing Brakes to Timbren Axle Less 3,500 lb Kit

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching