How Much Does the Erickson Horizontal E-Track # EM59150 Weigh

Question

Question:

What is the weight of the 2 foot section of erickson e-track? I know the load weights. I need the weight of the actual product. Thank you.

asked by: Anna

0

Expert Reply:

The 2 foot section of Erickson Horizontal E-Track # EM59150 that you referenced only weighs about 1 lb.

expert reply by: Jon G

0

click to enlarge

Answer 1

The 1" Long Black Torx Wall Liner Screw #WLS100 is the best option for the plywood installation. These screws are fine thread and made for metal studs. They have a tapping edge but often a starter or pilot hole should be drilled. You can then…

view full answer...

Answer 2

The legs for the CargoSmart Folding Workbench Brackets #3481744 will sit 22-21/2" away from the wall when in the deployed position, and then the brackets are 2-1/2" tall so they will stick out that far from the wall. My contact at…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

How Much Does the Erickson Horizontal E-Track # EM59150 Weigh

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching