Is RotaFlex Pin Box Similar to Mor Ryde Pin Box In terms of Cushioning

Question

Question:

Would you know how the roto flex compares to moryde and how much better if any the trail air airride would be?

asked by: Dale

0

Expert Reply:

The Mor/Ryde pin boxes and the Trailair RotaFlex like part # LC176440 are pretty similar in how they cushion the ride. The Mor/Ryde is definitely more common out there on the road, but the feedback I've read on people who have tried both said they were very similar.

expert reply by: Jameson C

0

Answer 1

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 2

The ride quality between the MORryde and the Rotaflex pin boxes are about equal. I did some digging and the Keystone owners seem to mostly like both of them about the same. Some people preferred one over the other but in general I would say you…

view full answer...

Answer 3

You are correct that in the Blue Ox SwayPro Owner's Manual they do recommend use molybdenum grease on both the hitch ball and the spring bars. The LubriMatic Moly EP Grease #LM54FR in a grease gun, such as #L30480, will work well. You could use…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is RotaFlex Pin Box Similar to Mor Ryde Pin Box In terms of Cushioning

Product Page this Question was Asked From

Continue Researching