Dimensions of the Lippert Slide-Topper Mounting Brackets for # LCV000163287

Question

Question:

For the mounting arm, how much room is needed for the mounting plate on the face of the slideout? I have a vent near the corner and I need to know if I have room

asked by: Galen P

1

Helpful Expert Reply:

My contact a Lippert Components confirmed with me that the mounting bracket on the Lippert Solera Slide-Topper Awning, # LCV000163287, measures from the center of the top rivet hole to the bottom of edge 1.050 inches.

The bracket will mount as close to the top trim of the slid out on you trailer, so from the bottom of this trim to the bottom of the mounting bracket will be no more than 1 to 1.5 inches. This will be enough clearance for the slider to mount to the slide out between the trim and the vent.

I recommend double checking the clearance between the bottom of the top trim and the top of the vent. If is wider than 1-1/2, you will have no issues with installing the slide-topper awning.

expert reply by: Jared P

1

click to enlarge

Answer 1

Without knowing the exact size of the current brackets I don't know if they will cover them. However the Solera RV Slide-Out Awning #LCV000182037 has mounting brackets that are 7 inches long, and the mounting surface is just over 1 inch before it…

view full answer...

Answer 2

To install a slide topper like the Solera RV Slide-Out Awning #LCV000168110 on a slide that already has a regular awning installed you will need to take a few measurements to ensure enough clearance. From the outside edge of the slide flange to the…

view full answer...

Answer 3

The 10' 10.5" replacement is part Solera RV Slide-Out Awning #LCV000184673, the 13' 7.5" replacement is the #LCV000168110 and the 8'8" is the #LCV000168325. I reached out to our supplier to confirm fit and given the flange…

view full answer...

Answer 4

The Tru Ryde grease seals you mentioned, part #RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application.

view full answer...

Answer 5

Hey Bryan, thanks for the information! The information Brinkley sent you corresponds to the Unitized Oil Seal for Trailer Hubs item #10-63, which is not available in a bearing kit. A unitized oil seal is a two-piece, self-contained unit where the…

view full answer...

Answer 6

I believe you are asking if the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182 will work with the Go Power PWM Solar Charge Controller #GP72RR, which is a 30 amp controller, and the answer to that is yes it will. It comes with…

view full answer...

Answer 7

The correct Solar package for you is going to depend on what your goals are and how much power you are using. I have included a help article that digs into calculating how much power you are using and what system is right for your wants/needs. I have…

view full answer...

Answer 8

Hello, sorry for any confusion. For determining the proper size Solera Slider your project requires you need to measure the total width of your slide room from the outside including the flange then add a minimum of 5" (2-1/2" each for the…

view full answer...

Answer 9

The access plate is 2-15/16" wide and 7-5/8" long and must be mounted on the slide out's outside wall as far up as it can, but not mounted on the t-molding. The t-molding is what looks like 6" wide trim around the outside slide out…

view full answer...

Answer 10

You do need 6 inches of clearance from the edges of your slide box in order to fit a Solera awning. To determine the correct slide-out awing you simply need to measure from flange to flange and the fabric will need to extend at least 2-1/2 inches…

view full answer...

Answer 11

I checked with Dexter and they indicate that for hub 008-386-80: "Available for service parts only." Meaning the actual hub assembly is not available but parts for it are such as the 35mm cartridge bearing #31-72-3. There isn't a way to…

view full answer...

Dimensions of the Lippert Slide-Topper Mounting Brackets for # LCV000163287

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching