Can Roller Bunks Be Used on Pontoon Boat Trailer

Question

Question:

Looking for an easier way to load and in load my pontoon boat. Its. 25ft sun tracker and I have a trailer with the angled wooden carpeted bunks. Would I be able to use the roller bunks on top? How many sets would I need? Thanks,

asked by: Oliver F

0

Expert Reply:

You can use roller bunks like the # DL21741 on your trailer. They can be attached to wood bunks like what you have too.

Without seeing your trailer it's hard to say what the best route would be, but people use roller bunks on pontoon boat trailers all the time.

expert reply by: Jameson C

0

Answer 1

Yes, you can use Roller Bunks #CE27700 with a pontoon boat trailer. These come in 4' long sections that you can attach directly on top of the bunk boards or you can use the V-Wing Bolster Bracket #CE26244G if you are concerned with raising the…

view full answer...

Answer 2

A couple sets of the Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers #DL21741 will drastically help with getting your pontoon boat on and off the trailer smoothly and easily as there isn't any friction…

view full answer...

Answer 3

I'll start off by saying that I've seen quite a few boat trailers that use a combination of rollers like the CE Smith Roller Bunks for Boat Trailers - 6 Rollers Each - 5' Long - 1,500 lbs - 1 Pair #CE27710 and a carpeted bunk like the CE…

view full answer...

Answer 4

You could use roller bunks such as #DL21740 on a pontoon boat trailer. If the pontoons sit on carpeted bunks and support the boat then you would need to place rollers the whole length of each of the carpeted bunks. Set #DL21741 is rated higher at…

view full answer...

Answer 5

Thanks for reaching out again, Mike! Yes, the 5' Long Boat Trailer Standard Roller Bunks #DL21755 will be able to easily handle the weight of your 3,200 lb boat. These have a 3,000 lb rating for the set so when using 2 sets they will be able to…

view full answer...

Answer 6

Sounds like you are trying to build a shoreline ramp like what you see in the picture I attached. For a flat bottomed boat like yours you could use roller bunks like part #DL21741 with them laying totally flat on the ramp and they would work fine.

view full answer...

Answer 7

The Fulton Marine Grade Carpeting, 8" Wide x 144" Long #FCR8008 will help your trailer bunk boards support your boat and protect it from unnecessary scratches, but it won't necessarily help it to slide better than other marine…

view full answer...

Answer 8

Hello Dave. In regards to the CE Smith Bunk Roller #CE27700 about half of the diameter of the roller sits above the metal rail, there is 1" (maybe 1-1/16") of clearance between the metal rail and the boat bottom when the boat is sitting on…

view full answer...

Answer 9

Roller bunks like the Dutton-Lainson 5 Foot Long #DL21755 that you're looking at are designed to be installed on a boat trailer but there's no particular reason they couldn't also be used to make a ramp. We have indeed had customers do…

view full answer...

Answer 10

The diameter of the mounting bolt hole on the CE Smith Bow Roller Bracket for Winch Stands, #CE31005PG, is .45 inch. The bracket uses a 5-1/4 inches long x 1/2 inch diameter steel shaft for attaching the roller/Y-stop, which is part #CE10700A.

view full answer...

Answer 11

This trailer was either set up this way by the manufacturer or the owners had to fabricate some extensions and then attach brackets and the stops to make this set up. Extensions would have to be fabricated by a machine shop or a welder and then you…

view full answer...

Answer 12

I am not familiar with the exact bow stop you have pictured but we do carry a few options such as the Yates Flat Bow Stop for Boat Trailers part #YRJONBLOCK which is what I recommend using. It's designed to be used with a bracket such as the CE…

view full answer...

Can Roller Bunks Be Used on Pontoon Boat Trailer

Product Page this Question was Asked From

Continue Researching