Will Reese Select Plus 5th Wheel Hitch Center Section Fit Draw-Tite 18k 5th Wheel Hitch 40163

Question

Question:

Will Reece replacement head 58293 fit the Draw-tite body?

asked by: Hans A

0

Expert Reply:

I spoke with my contacts at Reese and Draw-Tite about center section # 58293 and your Draw-Tite 18K 5th wheel hitch 40163. After doing some digging he determined that this center section is compatible with your hitch. This particular center section fits several Reese and Draw-Tite Select Plus series hitches so that is another way to determine compatibility.

expert reply by: Michael H

0

Answer 1

To upgrade to a single-piece, self-latching jaw and also increase the capacity of your 16K Reese 5th Wheel Trailer Hitch #RP30047, you can use the 20K Select Plus Fifth Wheel Head Kit #58292 along with the Head Support #58293. These will work with…

view full answer...

Answer 2

Hello Bill. 5th wheel hitch technology has come a long way in the last several years. If you are using an old hitch, it is definitely not uncommon to have issues like this. Most older hitches, and even some new lower-end hitches will chuck quite a…

view full answer...

Answer 3

I searched online for the owner's manual to find the capacities, and found the exact towing capacity for your 2016 Chevy Silverado 2500 with a short bed and 6.0L engine will depend on the cab size, and if you have 2WD or 4WD. From what I found,…

view full answer...

Answer 4

Yes you can convert your Reese 20k fifth wheel hitch to a slider hitch with just the base slider part #RP50024. I attached a picture of a customer who did exactly this.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Will Reese Select Plus 5th Wheel Hitch Center Section Fit Draw-Tite 18k 5th Wheel Hitch 40163

Product Page this Question was Asked From

Continue Researching