How to Mount the Erickson Sliding 15K Truck and Trailer Winch

Question

Question:

Where do I find the track for the sliding winch ?

asked by: G H

0

Expert Reply:

The Erickson Sliding 15K Truck and Trailer Winch, # E52809, was designed to mount to the channels that are found on the underside of long semi flat bed trailers.

If you are needing this type of channel any semi trailer fabricator or repair should have this item in stock. Usually the channel is sold in 8ft sections.

My contact at Erickson also confirmed that if needed, the winch can be welded to the frame of the trailer when installing.

expert reply by: Jared P

0

Answer 1

I went out into our warehouse and pulled a Sliding 15K Truck and Trailer Winch #E52809 to measure it and found that the bracket measures 5-1/2 inches wide by 7-1/2 inches long with a height of 4 inches. If you add in the reel the width goes up to 8…

view full answer...

Answer 2

When it comes to your 10,000 capacity trailer I recommend the Buyers Products Trailer Safety Chains #337B03822SC. They're made out of a zinc-coated steel. They're 22 inches long and the link diameter is 3/8 inches. I attached a review video…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 5

The best ball style trailer coupler lock we offer for a trailer with a lip is the Master Lock 1-7/8", 2", and 2-5/16" Trailer Coupler Lock part #379DAT.

view full answer...

Answer 6

Thank you for sending the photo! While I have a solution for you, the Blaylock Total-Encasement Coupler Lock, part #BLTL-23 will not work. I is designed to fit Bulldog Collar-Lok style couplers that use a 2-5/16" ball, like #BD028463 for…

view full answer...

Answer 7

It appears you have a spare tire carrier very similar to the Carrier #TR-1. This uses the Replacement Tire Mounting Hardware #2109 for new spare tire carriage bolts, nuts and spring retainers. It also includes new nuts for the u-bolts which you would…

view full answer...

Answer 8

From what I have found, the ALKO hub and drum assembly you have is for 7,000 lb axles. I believe the Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2 #8-219-4UC3 will work as a replacement. This has the same…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Do you by any chance mean 235/80-16 and 235/85-16? Because there isn't a 275 trailer tire size that I have seen. If so then the widths are the same between the two 235 sizes. The difference is overall diameter. The 235/80-16 is 30.9 inches in…

view full answer...

Answer 11

I was able to cross reference with the manufacturer and find the parts you need. I recommend the Dexter Hydraulic Trailer Brake Kit - Free Backing - 12" - Left and Right Hand Assemblies - 7K #23-342-343 if you don't need the parking brake.…

view full answer...

How to Mount the Erickson Sliding 15K Truck and Trailer Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching