D-Ring Diameter of Stake Pocket Anchors T55B and PK-SPTD

Question

Question:

what is the diameter of the d-ring? also what is the diameter of the d-ring on product PK-SPD?

asked by: Phil

1

Helpful Expert Reply:

The D-ring of the Stake Pocket Anchor part # T55B is 3/8 inch. The diameter of the D-ring on the # PK-SPTD is 7/16 of an inch. So basically it is 1/16 of an inch thicker.

expert reply by: Jameson C

1

Answer 1

Hello Richard, thanks for reaching out. I went out to our warehouse and measured the pin that comes with the Stake Pocket Tie-Down Anchor #BR72ZR. The pins are 6-3/4" long overall. So while the anchor would be a bit loose in a 5-1/2" stake…

view full answer...

Answer 2

I am happy to tell you that four of the Stake Pocket Tie-Down Anchor - Black Powder Coat - 2" D-Ring - 1,600 lbs #T55B that you ordered will indeed be strong enough to handle the 4,400 lb car you are going to haul. The working load limit (WLL)…

view full answer...

Answer 3

Hey Matt thanks for the question. I checked with our vendors and I do not have a Stake Pocket Tie-Down Anchor like item #BR72ZR that fits a 2" x 6" stake pocket. What kind of car trailer do you have?

view full answer...

Answer 4

I went out to the warehouse and measured the Replacement Tire Mounting Hardware for Bumper Mounted Tire Carrier #2109 and measured 12.76mm (1/2") for the spline diameter, 29.48mm (1-5/32") for the thread length, and the head diameter is…

view full answer...

Answer 5

We haven't heard from anyone with your specific trailer, but you can compare the dimensions of the #T55B to your trailer to see if it would fit or not. You would be able to take the dimensions in the picture I attached and compare them to the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

D-Ring Diameter of Stake Pocket Anchors T55B and PK-SPTD

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching