Replacement Parts for Bunk-Style Guide-Ons for Boat Trailer

Question

Question:

I am looking to purchase Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - 75-Degree Bend - 18inch - CE27609PG for a new installation and was wanting to know what other part numbers were needed minus the bunk boards themselves. Bunk brackets u bolts etc

asked by: Earl B

0

Expert Reply:

In order to piece together Bunk-Style Guide-Ons for your boat trailer, you will use the CE Smith Replacement Upright # CE27609PG mentioned in your question, along with the Replacement Mounting Hardware Kit # CE11452-A and Swivel Bracket # CE10206G. This will be everything you need excluding the bunk boards.

expert reply by: Chris R

0

Answer 1

It is possible to install CE Smith Bunkboard Guide-On Kit #CE27600K75 in the way you have suggested. But it may require trimming parts of the tubes should they interfere with the boat. The only part of the set up you would want to make contact with…

view full answer...

Answer 2

I can help you find the correct bolster and swivel brackets for your Seadoo trailer. The CE Smith part #CE10002G is a galvanized 13 inch bolster with a swivel bracket assembly. The swivel bracket will fit your 2 x 4 bunk great, but the brackets…

view full answer...

Answer 3

It sounds like you are trying to add some steps to the tongue of your boat trailer for help getting in the boat. If that is the case then only bolt-on option we'd have is the HitchMate Boat Trailer Step part #HE4036 which bolts onto the frame.…

view full answer...

Answer 4

There is an upright which may work for you, the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - Lanced - 39" #CE27605PG. This upright has a bottom leg of 23 inches, and is a replacement for CE Smith Post-Style Guide-Ons…

view full answer...

Answer 5

We do have a selection of fenders for 13" wheels that you can use to replace your current fenders. Among our linked selection we have different constructions like aluminum, plastic, and steel. These fenders can mount via brackets or welding…

view full answer...

Answer 6

Hey Joe, great question! I actually talked to one of the B&W reps about this exact thing when they were here a while back. For the B&W Companion 5th Wheel Hitch #BWRVK3300, the best place to start is the middle position (A). That’s the…

view full answer...

Answer 7

I did some research and found that the 12194TC seal you said you have measures 1.250 inside diameter, and 1.979 outside diameter. The seal I recommend is part #34823. The dimensions listed for this seal are 1.249 inside diameter and 1.983 outside…

view full answer...

Answer 8

You could always go with the taller 60 inch guide-ons, #CE27640, and trim as needed. But if you go to different places to use the boat, you never know how much of the trailer you will need to submerge and may find that the 40 inch would be too short…

view full answer...

Answer 9

No, 2 inch PVC would not fit around the Replacement Upright #CE27609PG. The upright is 1-1/2 inches square which means diagonally it is 2-1/8 inches. If you have PVC that has a 2-1/8 or slightly larger inner diameter such as #CE11354 then it would…

view full answer...

Answer 10

Hey Mark, thanks for reaching out! For just a swivel bracket we've for the Tie Down #TD44FR. This will work great with any or the roller bunks and help cut down on some of the cost of your upgrade. What roller bunks were you planning on going…

view full answer...

Replacement Parts for Bunk-Style Guide-Ons for Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching