Solution for Finding Salt Build Up in Demco DA70 Surge Actuator
Updated 09/08/2026 | Published 08/30/2026 >
Products Featured in This Question
Question:
I have a Demco DA70 on a single axle boat trailer that gets launched in saltwater. Ive found salt buildup in my brake fluid reservoir and the master cylinder spring is rusted. I can send pics by email. What are your recommendations.
asked by: Russell B
Expert Reply:
Hey Russell, I would go ahead and replace the master cylinder in your Demco DA71 with the part # 5672 for if you have disc brakes or the # 5650 if they are drum as the salt is most likely corroding the master cylinder from inside. I would also flush the brake lines too in case the salt got inside them as well.
In the future Demco recommends spraying down the setup with freshwater after it gets out of the saltwater to hopefully prevent this type of thing from happening again. Hows the rest of the braking system looking?
Product Page this Question was Asked From
Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Boat Trailer
- Construction Trailer
- Farm Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 7000 lbs GTW
- 2 Inch Ball Coupler
- 3 Inch Channel Tongue
- Drum Brakes
- No Lockout
- Demco
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: boat loading guide
- Shop: Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - 75-Degree Bend - 18"
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Article: Trailer Wiring Diagrams
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: Replacement Actuator for an Older Atwood 85736
- Q&A: Is There Manual Lockout Available for Demco Surge Actuator part # DM72VR
- Q&A: New Brake Assemblies, Hub/Drums, Brake Lines, and Bearing Buddy for Trailer with 3,500 lb Axle
- Q&A: Replacement for Atwood Surge Brake Actuator 85778
- Q&A: Can Demco Hydraulic Brake Actuator DM72VR Replace Atwood 61101?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Most Popular Wheel Bearings
- Article: Hydraulic Trailer Brakes: How They Work & What to Buy


Ken S.
9/4/2026
Russell, as a Demco DA70 user and a marine engineer with 32 years at sea on ships, my suggestions: 1--Flush your brake system once or twice a year if it is getting dunked in salt water. Water contaminates brake fluid, and salt water badly contaminates the entire braking system. Use a reverse pressure bleeder that bleeds from the wheel cylinders out through the master cylinder. You don't want to push salt water through the brake system from the contaminated master cylinder to the wheel cylinders. 2--In addition to washing with fresh water, my favorite anti-rust coating is LPS3, a thick waxy coating that has worked very well for me for both corrosion protection and good lubrication of sliding surfaces. WD-40 (40th try for the best water-displacing formula) is great for displacing the water on the metal surface but doesn't last long to prevent corrosion. 3--If you use grease on the sliding surfaces use a good waterproof grease like Green Grease or Mystic JT-6. Don't use a white grease; some allow rust quickly.