Recommended Bulldog Square Jack And Handle To Work With Bulldog Jack BD183750

Question

Question:

What is the appropriate companion jack to the product listed below when used in a tandem setup? Also, which crank handle is recommended? Thanks, BD183750

asked by: William B

0

Expert Reply:

If you are going to use the Bulldog 2-Speed Square Jack, part # BD183750 in a tandem setup you can use part # BD182701.

The crank handle needed for this is part # BD015181.

expert reply by: Jeffrey L

0

Answer 1

If you are simply needing to replace some worn equalizers then we actually do carry the part you are searching for. It is listed as part #K13-142-02 on our site and is a direct replacement for the 13-142 equalizer that you referenced. I confirmed…

view full answer...

Answer 2

Thank you for the pictures and information provided. While the Atwood 75721 motor and gear boxes are discontinued, we do have a gear box that will work with your Atwood 75721 motor and landing gear. - Replacement Gearbox for Venture Aluminum Electric…

view full answer...

Answer 3

If the replacing the gear box didn't fix the problem, then as long as the internals of the legs themselves are still in good shape replacing the motor would be the next logical step. Before doing that, I'd use the crank to operate the landing…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Recommended Bulldog Square Jack And Handle To Work With Bulldog Jack BD183750

Continue Researching