How to Wire Toyota Factory Brake Controller Harness to Aftermarket Harness on 2010 Toyota Tundra
Updated 10/24/2016 | Published 10/22/2016
Question:
Hi, Im looking to install a tekonsha prodigy p2 #90185 in my 2010 Toyota tundra, with the factory tow package. I have the Toyota tow harness which adapts to the connector under the dash, and is a 5 wire harnessright hand side of picture. The tekonsha has a 4 wire harnessleft hand side of picture. Any help on how to adapt the two together is greatly appreciated.
asked by: Matt
Expert Reply:
On your factory Toyota brake controller harness the black wire connects to the controller harness black wire, Toyota green with white stripe connects to brake controller red, brown connects to controller white, red connects to controller blue. The all green Toyota wire is not used so you can tape it up and stow it out of the way.
The functions as listed above are black/black for 12 volt power, green and white/red for input from the brake switch, brown/white for ground, red/blue for output to the trailer brakes.
Product Page this Question was Asked From
Draw-Tite Activator IV Trailer Brake Controller - Up to 4 Axles - Time Delayed
- Trailer Brake Controller
- Time Delayed Controller
- Electric
- Plug-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- LED Display
- Single Trailer Only
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ram
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Toyota and Lexus
- Shop: RV Covers
- Shop: Classic Accessories PolyPro III Deluxe RV Cover for Travel Trailers up to 27' Long - Gray
- Shop: Towing Mirrors
- Shop: Vehicle Lights
- Shop: CIPA Custom Towing Mirror - Slip On - Driver Side
- Shop: Pacer Performance Hi-Five LED Truck Cab Lights - Chrome Plated - 5 Piece - Amber LEDs - Amber Lens
- Search Results: c51140
- Video: Installation: Curt Discovery NEXT Trailer Brake Controller w/ Custom Harness on a 2012 Toyota Tundra
- Video: Curt Discovery NEXT Trailer Brake Controller w/ Custom Harness: The Breakdown
- Video: All You Need to Know About the Curt Discovery NEXT Trailer Brake Controller w/ Custom Harness
- Video: Installing the CIPA Custom Towing Mirror on your 2008 Toyota Tundra
- Shop: Vehicle Cargo Control
- Shop: Windshield Covers
- Shop: Performance Chip Tuners
- Shop: Draw-Tite Activator IV Trailer Brake Controller - Up to 4 Axles - Time Delayed
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Custom Harness - 1 to 4 Axles - Proportional
- Video: A Closer Look at the CIPA Custom Towing Mirror
- Video: How to Set Up Your CIPA Custom Towing Mirrors on a 2013 Toyota Tundra
- Video: Review of Redarc Trailer Brake Controller Wiring Harness - RED49FR
- Q&A: Brake Controller Port For Redarc Harness on 2014 Toyota Tundra
- Q&A: 2021 Grand Design Travel Trailer Toy Hauler Axle Components
- Q&A: Trailer Brakes No Longer Work After Driving With Breakaway Pin Pulled
- Q&A: Recommended Trailer Hitch and Wiring Harness for a 2025 Kia Sorrento Hybrid
- Q&A: Will Kodiak Trailer Hub for 3,500-lb Axles Fit Dexter 80043A Spindle On Boat Trailer
- Q&A: Help Picking Out Replacement Axle for 2004 Ranger Trail Trailer
- Q&A: Replacement Hub and Drum Assemblies for AL/KO 8460 Hubs and Drums
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Brake Controller
