Could the TorkLift HiddenPower Under-Vehicle Battery Mount Attach to Trailer Frame

Question

Question:

Can this be mounted to a trailer tongue on the frame??

asked by: Matt

0

Expert Reply:

Although the TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box # TLA7727 was originally designed for attaching to the frame of a truck you certainly could attach it to the frame of a trailer.

expert reply by: Jameson C

0

Richard O.

4/21/2020

I am also interested in using this item for a trailer frame. My trailer frame is 2x6 boxed. What is the dimention of the top of this battery tray where it hangs over the frame? Ie: How wide of a frame can it hang on? I am aware the bottom bracket isnt as wide but i can fabricate something that would be wider for my application. Thanks

Chris R.

4/27/2020

The top clamp of the TorkLift Battery Box # TLA7727 is designed to clamp around a frame that's about 2-7/8" wide. The frame on your trailer might actually be too small. A better option might be part # TLA7740, which can drill into the frame as well.

Answer 1

The TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box #TLA7727 has internal measurements of 14-1/2" L x 7-7/8" W x 9-3/4" T. This mount is a confirmed fit for your 2004 Ford F-350 with 8 foot bed. It is possible to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

We sure do Brian. We've actually got two center caps that are going to work with the Kenda Karrier KR53 ST205/75R15 Radial Trailer Tire with 15" Black Aluminum Wheel item #KE58JV. Which one you go with is going to come down to personal…

view full answer...

Answer 10

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 11

Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…

view full answer...

Answer 12

Hi Jeong-Won; the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX89FR fits a 3" wide trailer tongue without a specific height requirement. To add a hinge back onto the tongue you simply have to measure the height. If you have a 3"…

view full answer...

Could the TorkLift HiddenPower Under-Vehicle Battery Mount Attach to Trailer Frame

Product Page this Question was Asked From

Continue Researching