Solution for Securing Jack Handle from Dragging On Ground In Trails

Question

Question:

Hello, I have a sidewind trailer jack similar to PS1401060303. The handle hangs down and gets damaged when Im off in the trails. Do you have a clip or other solution to hold the handle up when the jack is in the storage position?

asked by: Adam B

0

Expert Reply:

Easiest way would be to use a strap like a bungee part # EM06701to wrap around the handle and jack body to hold the handle to the jack.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Fulton and he informed me that both the Fulton XLT Jack #F141133 and Fulton F2 Jacks, like #F1413040134, have a handle catch to help keep the jack handle from swinging when the jack is stowed. For a Fulton jack, I recommend…

view full answer...

Answer 2

The only trailer hitch we currently have confirmation of fit for a 2020 Chevrolet Bolt EV is the Curt Trailer Hitch Receiver part #C11457 which I confirmed by reaching out to Curt directly. The Curt Trailer Hitch is an excellent option for the…

view full answer...

Answer 3

Although it is not required by law, what you are wanting to do is certainly possible. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a vehicle-to-vehicle tail light…

view full answer...

Answer 4

Sounds like you are looking for a way to keep the handle of the Dutton Lainson jack part #DL22580 horizontal when the jack is in the horizontal, stored position. Most likely you want to this so the handle doesn't drag. This isn't a super…

view full answer...

Answer 5

Hey Daniel, I can help point you in the right direction. If I were you I would stick with the radial tires. Bias ply tires use a crisscross pattern for the layers of cord. This make for a more firm sidewall and this is more of an "old…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Solution for Securing Jack Handle from Dragging On Ground In Trails

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching