Reset Breakaway Lever of Titan Surge Brake Actuator

Question

Question:

How do you reset the Breakaway lever once its been activated

asked by: Richard

0

Expert Reply:

To release the breakaway lever of the Titan Zinc-Plated Brake Actuator # T4623800 you will need to use a screw driver to push the clip on the lever back towards the rear of the trailer while pushing the lever back to its original position.

expert reply by: Jameson C

0

Answer 1

Yes, the Fastway Zip Coiled Trailer Breakaway Cable #FA80-01-2160 that you referenced would work well as a replacement breakaway cable for your trailer. You would just need to remove your cable and clip this cable on and you would be ready to go. I…

view full answer...

Answer 2

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 3

For 3,500 pound axle U-bolt kits like the Redline #APUBR-1 that use 1/2 inch hex nuts you will want to torque them down somewhere between 45 and 70 foot pounds. I have attached a great article on trailer suspension that includes this info along with…

view full answer...

Answer 4

According to Dexter, the nut should be torqued to between 45-70 foot lbs. If you don't have a torque wrench close at hand, Tighten the bolts until the lock washer flattens, which will put you really close to the correct torque. We offer 4 nuts…

view full answer...

Answer 5

I spoke with a representative of Dexter who told me that the 4 mounting flange bolts on the Dexter Nev-R-Adjust Electric Trailer Brake Assembly #K23-478-00 (left hand) and #K23-479-00 (right hand) who was unable to confirm the specific torque specs…

view full answer...

Answer 6

The Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs #23-181 and Left Hand #23-180 should should be torqued to 30-50 foot/lbs.

view full answer...

Answer 7

To use with the 4-Leaf Double-Eye Spring for 3,500 Pound Trailer Axles #SP-210275 I recommend the U-Bolt Kit #APUBR-1. The manufacturer doesn't list any specified torque specs for this kit but based on the size of the hardware (1/2 inch diameter…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Reset Breakaway Lever of Titan Surge Brake Actuator

Product Page this Question was Asked From

Continue Researching