Replacement Shank Recommendation for Yakima Holdup for Use in 2 inch Hitch

Question

Question:

Hi, need to replace 1.25 shaft with 2. what model # do i need?

asked by: Rob Q

0

Expert Reply:

I checked with Yakima and they never made a bike rack called the StandUp. Are you possibly referring to the HoldUp # Y02443?

If so, the replacement shank for a 2 inch hitch is the part # Y8890278 for black or part # Y80126 for gray.

expert reply by: Jameson C

0

Answer 1

The Yakima HoldUp you referenced isn't a good choice for bike with fenders. The ratcheting hooks can't be tightened enough to get a good hold on the front bike wheels. For bikes with fenders a better choice would be one of the following bike…

view full answer...

Answer 2

I have a great solution for you. Here at etrailer, we do not recommend using wheel-mount style bike racks like the Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount #Y02443 with bikes with fenders. This is because we have seen…

view full answer...

Answer 3

A bike rack that holds the bike by the tops of the tires like the Yakima #Y02443 HoldUp wouldn't be the best choice for your style of bike because the presence of the fenders would prevent the rack's arms from getting a good grip on the…

view full answer...

Answer 4

The Yakima HoldUp 2 Bike Rack part #Y02443 is a wheel mount bike rack which cannot be used with bikes that have fenders. The reason for this is because the wheel hooks would have to be positioned too far forward on the tire because of the fenders so…

view full answer...

Answer 5

As you can see in the attached photo, customers have used the RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches #RKY10002 with bikes that have front fenders. While this may work for you, I still don't recommend doing this because the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hello Rick, Thanks for reaching out with all of the details about your setup. I checked with Dometic to make sure I could give you the best answer. The Dometic CT Single Zone Thermostat and Control Board Kit #DMC83ZR will not work with your Penguin…

view full answer...

Answer 11

Hey Doug, I checked with Curt and their hitch part #C58VV is a confirmed for all models of the 2026 Lexus RZ350e including the electric model so it would work great for you. Do you have a bike rack already? What kind of bikes do you have?

view full answer...

Answer 12

The Hollywood Racks Trail Rider 2-Bike Rack #HR200 weighs about 35 lbs. The Swagman XC 2-Bike Rack #S64650 is lighter at about 26 lbs. The biggest difference between the two is the Swagman rack is rated for 2 bikes at 35 lbs each and the Hollywood…

view full answer...

Replacement Shank Recommendation for Yakima Holdup for Use in 2 inch Hitch

Product Page this Question was Asked From

Continue Researching