Recommended Repair Kit For Roadmaster Sterling Tow Bar

Question

Question:

Need a rebuild kit what do I order. Sterling Tow Bar

asked by: Leighton N

0

Expert Reply:

If all you need is the bushing kit for your Sterling tow bar then part # RM-910003-40 is the kit you need.

We also offer a Complete Repair Kit for Roadmaster Sterling Tow Bar, part # RM-910003-30. This kit comes with rubber caps, locking springs, retaining rings, shoulder bolts, Nylock nuts, 1-1/2 inch diameter acetyl washers, 3/4 inch jam nut, 3/4 inch diameter acetyl washers, and 3/4 inch lock nut.

expert reply by: Jeffrey L

0

Answer 1

The first thing you should do is check the bar with a straight-edge to determine if it is bent. If you determine that it is straight you will need to disassemble it and clean it. There is a nut on the forward end by the pivots, and a keeper assembly…

view full answer...

Answer 2

If you can provide me with exactly what tow bar you have I may have better information for you but I had saw you were looking at parts for the older Roadmaster Sterling Tow Bar so I will assume that is what you have. In order to free the arms…

view full answer...

Answer 3

Looks like you have a round 4-way connector in the picture you submitted. The colors you mentioned aren't totally a match for standard colors but they are close. Normally the colors are: White - Ground Return Green - Right Turn and Brake Lights…

view full answer...

Answer 4

You've been doing some great research! I reached out to my contact at Roadmaster who said that the 2 kits you need to service your older Roadmaster Sterling tow bar are parts #RM-910003-40 and #RM-910003-30 like you referenced. These come with…

view full answer...

Answer 5

I spoke with my contact at Roadmaster about how to find the serial number to get the proper adapter to use with the Blue Ox base plates. You will need to spread the 2 arms apart on the tow bar and then look for the sticker where the two arms come…

view full answer...

Answer 6

We offer both complete Repair Kit #RM-910003-30 for the Roadmaster Sterling tow bar, as well as Inner Arm Bushing Kit #RM-910003-40. For just the Split Nylatron Bushing use part #RM-200029-00 which installs inside the larger outer arm of the tow bar…

view full answer...

Answer 7

Yes, the Replacement Roadmaster Sterling Towbar Shank Assembly #910019-40 is a fit for all of the Roadmaster Sterling models. The current one they have active is the 8K #RM-576 but this same shank/stinger was used on the following discontinued models…

view full answer...

Answer 8

Hello Robert, thanks for reaching out. We do offer a repair kit for the Roadmaster Sterling tow bar, the Complete Repair Kit for Roadmaster Nighthawk, Sterling, and Sterling All-Terrain Tow Bars #RM-910003-30. This includes new shoulder bolts, nuts,…

view full answer...

Answer 9

I spoke to my contact at Roadmaster and he informed me that there is no way to adapt your older style Roadmaster tow bar to the new stinger. If yours is still good and you were just looking to replace the stinger as preventative maintenance I would…

view full answer...

Answer 10

Hello Teresa! Congrats on the new Jeep! Here is a list of parts you will need to flat tow it behind your RV. -Base Plate Kit: If you 2025 Jeep Grand Cherokee does NOT have lower air shutters: Roadmaster Direct-Connect Base Plate Kit - Removable Arms…

view full answer...

Answer 11

Yes, the Inner Arm Bushing Kit for Roadmaster Sterling Tow Bars #RM-910003-40 and the Complete Repair Kit for Roadmaster Sterling Tow Bar #RM-910003-30 are both correct for your Roadmaster Sterling tow bar that has a serial number 11019.

view full answer...

Recommended Repair Kit For Roadmaster Sterling Tow Bar

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching