Brake Mounting Flange Available for 8,000 Pound, 3-1/2 Inch Axle.

Question

Question:

do you sell a flange for the 8k dexter brake 12-1/4x3-[3/8inch if so what number and cost thx

asked by: Ben

0

Expert Reply:

If you're looking for a brake mounting flange for an 8,000 pound axle, you can use the Dexter Axle Trailer Brake Mounting Flange for 3-1/2 Inch Axles, 12-1/4 Inch Brake Assemblies # 4-50. This brake mounting flange has 4 mounting holes and is designed to be welded to the end of the axle to provide a mounting location for brake assemblies. This mounting flange will work well with 12-1/4 inch brake assemblies and the Dexter Hub and Drum Assembly you referenced # 8-218-9.

The inner diameter of the flange's pilot hole is 3.01 inches. Pricing for the product is listed on the product page, as well as in the product information at the end of this question.

If this is not the flange you were referring to, please let me know and I will be happy help.

expert reply by: Victoria B

0

Answer 1

Electric brakes such as Electric Trailer Brake Kit #AKEBRK-8 do not fit specific axles. These are 8,000 lb rated brakes with a 4-bolt mounting flange pattern and are 12-1/4" diameter x 3-3/8" wide, so you would need that mounting bolt…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Brake Mounting Flange Available for 8,000 Pound, 3-1/2 Inch Axle.

Products Featured in This Question

Continue Researching