How to Install a Brake Controller in a 2013 GMC Sierra 1500

Question

Question:

Is there a plug and play adapter for the Tekonsha Primus IQ and a 2013 GMC Sierra 1500? Thank you.

asked by: Cindy

0

Expert Reply:

For your 2013 GMC Sierra 1500 no brake controller plug/port is present under the dash, but the needed wires are already run. You will connect the brake controller wiring with the vehicle wiring already present under the dash.

If you check out the install video and help article I attached you will see exactly how to install the Tekonsha Primus IQ part # TK90160 in a truck like yours.

expert reply by: Jameson C

0

Answer 1

According to my contact at Tekonsha the Sentinel is an older brake controller and the lighting configuration that you have stated seems to be normal. If the green light is flashing at approximately an 8 second interval, it is a diagnostic light that…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 8

Hey Doug, welcome back! Yes, we have the Andersen Ultimate Safety Chain Kit with Clevis Hooks #RM3230. This is the complete kit, Andersen doesn't have the attachments available individually. It is specifically designed for the gooseneck mount…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How to Install a Brake Controller in a 2013 GMC Sierra 1500

Featured Help Information

Miscellaneous Media

Continue Researching