Boat Trailor Fender Recommendation for a Spartan Boat Trailer SR-210

Question

Question:

I have a Spartan Boat Trailer SR-210 that I’m looking for replacement fenders. Present fender is 34 ½” long by 10” wide and 9” high. Flat area is 5” by 7”.

asked by: Randy N

1

Helpful Expert Reply:

Thanks for submitting a picture of your current fender. It looks like the closest thing we offer to what you have would be the part # F008574. The dimensions of the fender are 9.7" wide x 43.4" long x 12.75" tall.

I attached a review video and an dimensional drawing for the fender as well. It may not match what you have perfectly but it should work well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

This is a common issue with the old Spartan Trailers. Unfortunately we do not have any fenders with that kind of mounting style. The Fulton Single Axle Trailer Fenders #F008574-2 (for white) or the Fulton Single Axle Trailer Fenders #F008584-2 (for…

view full answer...

Answer 2

The most important measurement is the mounting bracket slots and the Fulton Single Axle Trailer Fenders with Top and Side Steps #F008574-2 fit 14 inch wheels and measures 30-1/4 inches from inside to inside for the mounting brackets, which do not…

view full answer...

Answer 3

To use the brackets #PF775-BKT-2 to install the fenders #F008573 you may have to use a spacer to take up the 1-1/2 inches of the I beam's overhang so that the fender will make it all the way onto the bracket.

view full answer...

Answer 4

Yes, if you have 12" wheels now and want to move to 13" wheels you can use the CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 13" Wheels #CE19503-2. The #CE19503-2 will work fine with your current 12"…

view full answer...

Answer 5

If you are wanting a metal fender and you can verify your tires are 13 inch or 14 inch I recommend the Single Axle Trailer Fender w/ Backing, part #HP79VR. This fender is constructed of 16 gauge steel and will mount to your trailer after you drill…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...