Detail K2 Elite Snowplow for 2" Hitches - 84" Wide x 22" Tall
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Part Numbers: K2AVAL8422ELT,31367
Retail:$3,044.98
Our Price: $2,562.46
You Save: $482.52
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near meDetail K2 Elite Snowplow for 2" Hitches - 84" Wide x 22" Tall
part number: K2AVAL8422ELT
Hitch-mounted residential plow has shock-absorbing springs and a steel-edge blade to easily clear driveways and parking lots. Long-lasting actuator with internal clutch and wireless remote lets you raise or lower the 3-position blade from your cab.
Features:
- Hitch-mounted snowplow lets you clear paved and gravel parking lots and driveways with your vehicle
- Electric actuator raises and lowers plow smoothly and consistently
- Wireless remote control lets you operate plow from the warmth of your cab
- Internal clutch prevents damage caused by overextension of actuator
- Simple, chain-lifting design has fewer moving parts than other plow-lifting devices for a longer-lasting system
- Adjustable, 3-position blade can be manually angled left, right, and straight ahead
- Strong rubber deflector on top of plow directs snow down and away from your windshield
- Hardened steel edge breaks up packed snow and ice
- Skid shoes let you adjust plow height to scrape over gravel and uneven surfaces
- Shock-absorbing springs let plow tip forward on impact to protect you and your vehicle
- Can extend life of the plow if you hit an obstruction
- Blade stiffeners provide 2 additional points of contact between the plow and your hitch for a sturdy connection
- Red visibility markers help you see plow edges so you can steer away from obstacles
- Flip-down caster wheels allow you to roll the plow where you need it for mounting or storage
- Wheel height is adjustable to match your vehicle height
- Plow handle with knob lets you easily move plow up and down during mounting
- Safety chain holds plow in raised position during travel
- Reinforced, all steel construction has black, rust- and UV-resistant powder coat finish
- ISO certified
- Simple installation
- Slides into your vehicle's 2" front trailer hitch receiver
Specs:
- Application: 2" x 2" hitch receivers
- Cannot be used with hitches or receiver adapters that have built-in drops
- Blade dimensions: 84" wide x 22" tall
- 3 Blade angles:
- Left 45 degrees
- Straight ahead
- Right 45 degrees
- Distance from center of hitch pin hole to the front edge of plow: 50"
- Weight: 283 lbs
- 1-Year limited warranty
The Detail K2 Elite snowplow conveniently slides into your vehicle's front-mounted trailer hitch for fast, simple mounting. Easily raise and lower the plow from the comfort of your cab with the remote-controlled wireless actuator. The pivoting blade makes this plow ideal for rocky or uneven surfaces because it can adjust to the terrain.
Simple, Hitch-Mounted Installation
This hitch-mounted snowplow simply slides into your vehicle's front trailer hitch receiver, making it a breeze to install. A plow that attaches to custom-fit brackets ties you down to just 1 vehicle. But this hitch-mounted plow can be used on most trucks or SUVs with a 2" x 2" front-mounted hitch. As a result, this plow can be easily switched between multiple vehicles. And because it offers a nearly universal fit, you won't have to buy a new plow when you replace your old vehicle.
To install the Elite snowplow, just slide the shank of the plow assembly into your 2" trailer hitch receiver (sold separately). Then use a pin and clip or a hitch lock (sold separately) to secure the plow in the receiver.
The Elite snowplow comes with flip-down caster wheels that make the installation process even easier on you. Simply flip the wheels into position and you will be able to roll the plow into position for mounting or storage. The height of the wheels can also be adjusted to match the height of your vehicle.
How to Plow
Once the plow is mounted on your vehicle, lower the blade and set it to the desired angle. To set the angle, exit the vehicle and manually position the plow straight ahead, to the left, or to the right. Angling the blade allows you to push snow off to the side where you want it without having to change the angle of your entire vehicle. This is especially useful on a driveway or a private roadway where piling the snow straight ahead would create a barrier.
To begin plowing, just drive forward. When backing up to take another pass, be sure to lift the plow with the remote, then lower it again before moving forward. When approaching a large pile of snow, be sure to decrease your speed. Slamming into a pile of snow can void the warranty on the snowplow.
When you are finished, put your vehicle in park and lower the plow. Remove the plow from your vehicle after every use.
Smooth, Controlled Lifting with Electric Actuator
The electric actuator on this plow allows you to lift and lower the blade using either a toggle switch that installs in your cab or the included wireless remote control.
To raise the plow, use the switch or remote to activate the actuator. As the actuator moves along the internal screw, the arm on top of the actuator will pivot, raising the plow blade by pulling the chain that is attached to it. This simple, chain-lifting design has fewer moving parts than other plow-lifting devices, so the setup is less complicated and there are fewer parts to have to repair or replace.
This actuator lifts and lowers the snowplow blade smoother than an electric winch. In addition, fewer amps are required to run an actuator than to operate an electric winch, which means that the solenoid on the Detail K2 Elite will last twice as long as the solenoid on a plow that uses a winch. There is also a built-in clutch that prevents damage to the actuator if you try to raise the blade too high or drop it too low. The electric actuator is built to withstand extreme temperatures and wet conditions with its completely sealed gearbox and housing.
Detail K2 Features
The snowplow features skid shoes that allow you to adjust the height of your plow. This allows you to efficiently plow over surfaces that are uneven, such as gravel roads.
Blade stiffeners, or blade support brackets, reinforce the connection between the plow and your vehicle. They add 2 additional points of contact with your hitch on either side of the plow's T-frame. This prevents stress on the frame and on your vehicle, while also strengthening the performance of the plow.
Shock-absorbing springs allow the plow to dip forward in the event that you hit an obstruction. This flexibility protects you and your vehicle from impacts.
AVAL8422ELT Detail K2 Elite Hitch Mount Snow Plow - 84" Wide x 22" Tall Blade
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
part number: 31367
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Features:
- Front-mount hitch provides attachment point for hitch-mounted accessories
- Winch, spare tire carrier, snowplow, cargo carrier and more
- No more blindly backing trailer in - just hook it up and drive it forward
- Custom fit is designed specifically for your vehicle
- Precision, robotic welding maximizes strength and improves fit
- Easy, bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Gloss black powder coat finish over steel resists corrosion
- Sturdy, square-tube design
- Assembled in USA
Specs:
- Line pull: 9,000 lbs
- Vertical load: 350 lbs
- Gross trailer weight: 3,500 lbs
- Receiver opening: 2" x 2"
- Pin hole diameter: 5/8"
- Limited lifetime warranty
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
31367 Curt Front-Mount Trailer Hitch Receiver
Customer Reviews
Detail K2 Elite Snowplow for 2" Hitches - 84" Wide x 22" Tall - K2AVAL8422ELT
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" - 31367
Average Customer Rating: 4.8 out of 5 stars (53 Customer Reviews)
Hitch-mounted residential plow has shock-absorbing springs and a steel-edge blade to easily clear driveways and parking lots. Long-lasting actuator with internal clutch and wireless remote lets you raise or lower the 3-position blade from your cab. Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.by: John09/03/2022
A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.
by: John12/16/2023
Lexus
Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.
by: Henry01/15/2024
2010 GMC Terrain
I had great personnel service, and the Hitch Receiver is solid. The material is heavy duty, and the welds are first class. Second item I've bought from etraier and both time I have been 100 percent satisfied. I go offroad and I use the hitch to hold a 2nd spare tire. I just got back from a 1,500-mile road trip to the Naveda mountains, in rough terrain, in 7-degree weather and many feet of snow and it held perfect. American made is the only way to go when your life depends on it.
by: Curtis02/16/2023
2009 Toyota 4Runner
Fit perfectly on my 08 Lexus GX470. Super excited for the additional functionality of having a front hitch. I move trails around my tight yard but also will enjoy putting a cooler on the front cargo rack, and having my hitch mounted winch up front. So versatile.
by: David08/07/2020
2007 Toyota 4Runner
Okay, first things first. I installed this hitch on a 2006 4Runner, even though the hitch wasn't specifically for that model year (Curt says the hitch fits 2007-09 4Runners). The 2006 4Runner's front tow hooks are angled down, which is a requirement for this hitch to fit (see the picture). One snag I ran into was that the four bolt holes along the top of the hitch didn't quite line up with the bolts on my 4Runner (the holes were not quite far enough apart) so I took the hitch to a machinist who elongated the holes for me. I don't know if this mismatch was a manufacturing defect in the hitch, or whether it was due to the difference between a 2006 4Runner and the 2007-09 models. Once I fixed the hole spacing, the hitch installed fine. Seems like a solid hitch. Planning to use it to push a trailer around when parking it.
David
8/8/2021
This thing is great! Its so much easier to push a trailer around using a front hitch than it is to back it with the rear hitch. I can push this thing up a long curvy driveway with no trouble. Definitely recommended.
by: Bruce08/30/2016
2008 Toyota 4Runner
I installed this on my 2008 Toyota 4runner in order to back my pop up camper down an inclined very tight drive. It was difficult to use the rear hitch because I did not have enough room to straighten out the 4runner. I did it with the front hitch on the first try! My wife says it saved our marriage! Putting the camper away was the most stressful part of the trip before this. I did need to buy a longer ball hitch of a different height because the front hitch sits lower and further under the bumper. Etrailer quickly shipped exactly what I ordered
Bruce
9/4/2017
I just used it again today, and it is still working great. Glad I got it.
by: Rich12/31/2020
2007 Toyota FJ Cruiser
Great Fitting Hitch for the front of my FJ Cruiser. I needed a solution to re-use a personal plow from another vehicle. Luckily, the plow was able to be converted to a 2" receiver hookup. Using my existing winch for the up/down with a snatch block. Even with aftermarket Warrior Bumper and Skid Plates fit perfectly. Ground clearance not compromised. 6 bolt installation, EASY PEEZY.
by: Jeffrey Rhodes09/15/2022
I love my new front hitch. Shipped ahead of time and easy to install. Works great when moving the boat into the garage.
by: GJM12/27/2011
2011 Toyota FJ Cruiser
Fast and reliable shipping. Quality product and easy install.
*Plastic front piece on bumper bends ever so slightly for tow hitch to fit.
by: Gary 12/20/2023
I simply love it, it does everything I need it to do.
by: Edmund G.04/03/2012
2010 Toyota FJ Cruiser
I have attached pictures of the Fj with the front tow.
by: Dave Rust09/28/2015
2010 Toyota FJ Cruiser
The front mount Toyota FJ Cruiser hitch fit perfectly. It took me 30-45 minutes to install. you need a 145mm socket or wrench and a larger socket for the bolts that come with the kit (I used an adjustable). Good clean install using a total of 6 bolts (4 existing and 2 new that bolt to the factory tow points.
Excellent Kit!!! very happy!
Dave R.
9/29/2016
The front hitch works great! I should have bought this sooner!
by: Sid H.09/10/2013
2007 Toyota FJ Cruiser
What a value!! I installed this front receiver hitch on my 2007 FJ Cruiser and is was a perfect fit. I planned to use it for a bicycle rack mount when pulling my boat but use it also for a winch mount, access step for under the hood and for trailer handling in tight spaces. Super fast shipping from etrailer.com and great price too!!
Thanks, et!!
Ed
9/30/2013
were you able to keep the grey front skid plate with the front receiver installed. ive been researching but cant get a definite answer. the vid for install doesnt have it on.
by: William 10/04/2023
Toyota FJ Cruiser
I think this unit will work very nicely for being able to run my winch from either the front or the rear of my FJ Cruiser.
by: Alexander08/15/2018
2007 Toyota FJ Cruiser
Because of my complicated parking configuration I required a front mount hitch. The product came quickly right to my door. Installation on my 2007 Fj Cruiser was so simple and took no more then 30 minutes.
Thanks!
Alexander J.
8/15/2019
Still doing its job of parking the trailer!
by: Dan 10/02/2023
2010 Toyota FJ Cruiser
Great product!
by: CHRIS06/10/2019
I bought this for the front of my 4-Runner to carry a bike rack. I have not used it to tow a boat or trailer, For my use it is excellent.
Chrisg.
6/11/2020
Great - love it
by: Greg R.12/24/2020
Fit my 2006 4Runner perfectly. Some have had issues installing this hitch on a 2006 4Runner here in the reviews. I purchased this 31367 hitch in February 2019, but did not get around to installing it until today, December 2020. The installation was quick and simple. Removed four nuts connecting the bumper to the frame (but four bolts remain so the bumper stays intact) by using a couple drops of Liquid Wrench (like WD40, but more aggressive penetration) on each to help loosen them with the 1/2" drive breaker bar (about 16" long) and 14mm socket. Then lifted the hitch in place to hang on the bolts and placed the nuts on snug but not tight. The hitch comes with two 24mm bolts that then go through front hitch plates, front vehicle tow hooks, and have a heavy duty rectangular 'washer' used on the under side of the tow hook to bolt the front hitch to the tow hooks. These vehicle tow hooks must be angled down at 45degrees (straight out about 1/2" then down at 45degrees) to match the front hitch mounting plate which is also at 45degrees. As shown, the front hitch has replacement tow hooks welded to it, so you still have hooks after mounting. I then tightened the two 24mm bolts and then the four 14mm bolts. Done in about 45 minutes from box open to box in the recycle bin.
by: mike w.03/23/2015
2014 Toyota FJ Cruiser
For 2014 fj cruiser; will not fit until you cut-off the two inside lower mount bolts that do not attatch the front bumper brackets at the end or front of the frame. Not sure why these bolts are there, but may be by Toyota for some other option. Haad to cut-off then grind the remaining remnant f the stud before installation could proceed.
J W.
3/29/2015
Did you use hack saw or some easier method of cutting off bolts. Did you find what use these bolts were mounted for.
by: Deborah10/01/2022
Bolt holes did not line up. etrailer was no help. Many unreturned calls and unhelpful emails and unanswered questions, and no solutions offered. Finally gave up. Will probably have to have it welded on.
When they asked me to review it after one year (now), I stated the above to them. Their response was: "etrailer is continuously looking for ways to improve our customers' experience and we take your comments very seriously. Without honest feedback from valued customers like you we would not know where we need to make improvements." But again, offered no help or solution.
by: Gary R07/14/2020
Couldn’t be happy with my purchase. Has been holding up great!!
by: Ariana06/14/2021
Holds two fat-tire e-bikes securely. Easy to mount the bikes and remove them. Perfect solution for us as our airstream cannot accommodate a bike rack. Very satisfied with this product and would recommend it to anyone needing a front rack. Additionally, etrailer customer service is above and beyond. We will be using them again when needed for sure!
by: Lloyd 08/23/2023
Ordered a 07 model and it worked perfectly on my 06 4 Runner
by: Friedom G02/16/2017
2011 Toyota 4Runner
I've used my front hitch off and on for a year now, and without apology. I've taken it on aggressive 4x4 trails scraped on boulders, carried cargo 1000 miles, towed vehicles, pulled stumps, and it's a solid as ever! Very happy, it does everything I wanted.
25
53
Show More Reviews Ask the Experts about this Snow Plow
Do you have a question about this Snow Plow?
- Will A Leveling Kit Be Required To Use A DK2 Elite Snowplow
- The Detail K2 Elite Snowplow for 2" Hitches # K2AVAL8422ELT doesn't require a leveling kit or list any specific heights that the front-mounted hitch needs to be at so you should be fine without one. That being said you are adding a considerable amount of tongue weight to the hitch so you could run into very little clearance between the ground and snow plow components.
This plow has a shipping weight of 334lbs so you can expect it to be close to 330lbs once all the packaging is removed
view full answer... - Recommended Snowplow for a 2024 Jeep Wrangler Unlimited
- I recommend using the Detail K2 Elite Snowplow # K2AVAL8422ELT on the front of your 2024 Jeep Wrangler Unlimited. This will attach using a Front Receiver # C31086 so you will be able to easily remove and install the plow when needed. I prefer this plow as it uses an actuator which is better than a winch style since you do not have to worry about snow and ice collecting in the cable/strap.
view full answer... - What Is the Required Receiver Height for the Detail K2 Avalanche Elite Snowplow
- The Detail K2 Avalanche Elite Snowplow part # K2AVAL8422ELT will work with a front mount trailer hitch that is between 9" to 18" from the ground to the bottom inside edge of the receiver tube according to Detail K2. The blade height is adjustable which is why there is such a large range.
If your front mount trailer hitch is not within this range then your only option is to use a drop front mount trailer hitch. If you can let me know the year, make, and model of the vehicle I can see
view full answer... - Which Front Hitch Receiver for 1997 Ram 2500 to Mount Detail K2 Avalanche Snow Plow
- You can use the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" # 31604 on your 1997 Dodge Ram 2500 with Extended Cab and long bed, which would give you the front mounted hitch receiver you need to carry the Detail K2 Avalanche Elite Snowplow for 2" Hitches - 84" Wide x 22" Tall # K2AVAL8422ELT. Additionally, you would not need any type of drop adapter for this setup.
You could also use the Detail K2 Avalanche Snowplow for 2" Hitches - 84" Wide x 22" Tall # K2AVAL8422, which
view full answer... - Replacement Option For Bent 84" Snowplow
- We may have the replacement parts you are looking for, but I would need to know the brand and model of your current snow plow to confirm the correct parts.
If there are not parts available, or if you would rather not deal with having to change them another option is to replace your current plow with a similar snowplow like the 84" wide x 22" tall Detail K2 Avalanche Elite Snowplow for 2" Hitches # K2AVAL8422ELT which can be angled 45 degrees to left and right or can be used straight
view full answer... - Will Curt Front Hitch Receiver Fit a 2013 Toyota FJ Cruiser with Expedition One WyoOtto Bumper
- The front mount hitches we carry for your 2013 Toyota FJ Cruiser including # 31367 are designed to fit stock vehicles. But looking at pictures of the Expedition One WyoOtto bumper versus the stock bumper it does not appear that the new bumper hangs down any lower than the stock bumper. Provided that the new bumper uses the same mounting locations as the stock bumper and none extra needed by the hitch (see linked instructions) then I am confident it will fit. I have linked a video showing
view full answer... - Does Install of Curt Front Hitch # 31367 on 2014 Toyota FJ Cruiser Require Cutting of Bolts
- Several years ago we did have one customer who reported that they had to cut bolts for the Curt front hitch part # 31367 to fit their 2014 Toyota FJ Cruiser but we haven't had any other customers report the same thing so I would not anticipate it being a requirement for you as well.
view full answer... - Recommended Front Hitch for a 2011 Toyota FJ Cruiser w/ a Motorcycle Carrier
- Yes, it can and thanks for the picture! The Curt Front Trailer Hitch item # 31367 has a 350 lbs vertical load limit. So long as your carrier weighs 90 lbs or less this set up will work great with your 2011 Toyota FJ Cruiser.
I have linked an installation video below to help you get this hitch installed.
If you need a motorcycle carrier, I recommend the etrailer Motorcycle Carrier w/ Ramp item # e98873. This carrier has a 500 lbs capacity and weighs only 58 lbs.
view full answer... - Does Skid Shield Stay in Place on a 2014 Toyota FJ Cruiser when Installing Curt Front Mount Hitch
- The Curt front mount trailer hitch # 31367 should fit forward of the skid shield on your 2014 Toyota FJ Cruiser. It should be just like the video I have linked to the right on a 2008 FJ. You can see the skid shield stays in place parts of this video. Curt does list this hitch as a fit for all models of the 2014 FJ Cruiser so that would include models with the off road package.
view full answer... - Correct Front Mount Hitch for 2016 Toyota 4Runner SR5
- The Curt # 31367 front mounted hitch fit 2007-2014 Toyota 4Runner Tail Edition models.
For the 2016 SR5 model, you'll want to use part # C31076.
view full answer... - Will Front Mount Trailer Hitch, # 31367, Fit a 2008 Toyota FJ Cruiser with Trail Team Package
- I spoke with my contact at Curt on whether or not the Front Mount Trailer Hitch Receiver, # 31367, can be installed on your 2008 Toyota FJ Cruiser with the grille guard in place. While he did not have any notes stated that it would not fit the Trail Team package models, he could not say for sure that it would fit.
I have included a link to the instructions below. Take a look at the mounting points for the hitch and then where the grille guard is mounted on your FJ Cruiser. If they use
view full answer... - Steel Thickness of Curt Front Mount Receiver Hitch # 31367
- I went out to our warehouse and measured the thickness of the steel on the Curt Front Mount Hitch Receiver # 31367 with a digital caliper. The steel on the crosstube measured 0.255 inch thick and the steel on the mounting brackets are 0.342 inch thick. The tow hooks themselves have a 1/2 inch diameter.
I have attached an image to assit.
I have not heard of a customer modifying this particular hitch so that it fits your 2003 Toyota 4Runner so I am not sure what that process would
view full answer... - Troubleshooting Installation of 2008 FJ Cruiser Front Mounted Hitch
- With factory bolts, there is often thread locker or binding from time and debris. I recommend using a penetrating oil lubricant to work into the threading to allow you to loosen the nut. I recommend spraying the oil all the way around the nut only where it makes contact with the bolt and then using a wrench and mallet to add vibration to that nut. The vibration will help the oil get inside and loosen the hold. You may need to use a breaker bar to get the torque needed to loosen the
view full answer... - Can Curt Front Mount Trailer Hitch Receiver for a 2008 Toyota FJ Cruiser be Used with a Winch
- Sure, you can definitely use the Curt Front Mount Trailer Hitch Receiver, part # 31367, to mount a winch on the front of your 2008 Toyota FJ. Just keep in mind the weight capacities of the hitch and winch in comparison with the weights you will be pulling. The hitch has a 9,000 lb vertical line pull capacity.
I have also included a link to a video of this hitch being installed on a 2008 FJ.
view full answer... - Can Dirt Bike Carrier be Mounted to Front Hitch on Toyota FJ Cruiser
- Yes, you can absolutely mount a dirt bike carrier such as the Ultra-Fab # UF48-979033 or etrailer # e98873 to the Curt Front Mount Trailer Hitch Receiver # 31367.
I can verify as well that this hitch is a fit for the 2007 - 2014 Toyota FJ Cruiser.
In regards to legality you will want to check your local laws.
view full answer... - Does Front Mount Hitch For 2013 Toyota FJ Cruiser Fit With Smittybilt M1 Bumper
- I took a look at the installs for both, and the Curt Front Mount Trailer Hitch Receiver # 31367 will not fit with a Smittybilt M1 front bumper on your 2013 Toyota FJ Cruiser.
They use the same bolts on the frame rails so the bumper and hitch will interfere with each other.
view full answer... - Is It Possible The Curt Front Hitch 31367 Could Fit 4Runner Models Prior To 2007?
- Hey Trenton thanks for the question. You are correct that the Curt Front Mount Trailer Hitch # 31367 technically is not a confirmed fit for the 2003 Toyota 4Runner. Per the manufacturer it is only made for 2007-2009 models.
That being said, we have had several of our customers report back to us and say that the # 31367 hitch can be made to fit model years prior to 2007. I have included a few screenshots of some customer reviews below. It sounds like in both cases the hitch was successfully
view full answer... - Recommended Front Mount Hitch And Bike Rack For 2010 Toyota FJ Cruiser With Backup Camera
- With the backup camera mounted in the middle of the spare tire hub on your 2010 Toyota FJ Cruiser, it will be impossible to find a spare tire mounted bike carrier that would not interfere with the camera. Installing a rear hitch on your Cruiser and installing a bike rack would block the camera as well.
My only recommendation would be to install a front mount hitch like part # 31367, on your Cruiser. You could then use a bike rack on the front of your vehicle. This hitch has a 350 lb
view full answer... - Can A Front Mount Trailer Hitch Receiver Be Installed On A 2008 Toyota Highlander?
- I may have another option for you, but the Curt Trailer Hitch Receiver #31367 is only confirmed to fit a 2007-2009 Toyota 4Runner, 2007-2014 Toyota FJ Cruiser, and 2010-2013 Toyota 4Runner Trail Edition.
At this time there is not a custom fit front mount trailer hitch confirmed to fit your 2008 Toyota Highlander but that does not mean that a universal option like the Draw-Tite # 41990-07 cannot be installed. You would need to have a local fabricator modify it and weld it to your vehicle.
view full answer... - Does the CURT Front Mount Trailer Hitch # 31367 Fit a 2011 Toyota 4Runner Trail Edition
- CURT does list the Front Mount Receiver, # 31367, as a fit for the Trail models of the 2011 Toyota 4Runner. I have included a link to the installation instructions for you to view so you can compare them to your 4Runner. I have also included a link to a video showing a typical installation.
view full answer... - Fit of Curt Front Mount Receiver # 31367 on 2007 Toyota FJ Cruiser
- The Curt front mount receiver, part # 31367 is indeed a fit for your 2007 FJ Cruiser.
I have provided links to install instructions and an install video showing the receiver being installed on a 2008 FJ Cruiser.
view full answer... - Is there a Front Hitch for a 2004 Toyota 4Runner?
- No, I am sorry I do not. I also checked with our vendors and it doesn't look like anyone made one for the 2005 Toyota 4Runner.
The only option I have for you is to use the Curt Weld-On 2" Receiver item # E17 to have a custom fabricated hitch created at your nearby fabrication shop. This receiver will give them an easy plate to weld to for the receiver end and give you a hidden design.
view full answer... - Front Mount Receiver Mounting Hole Spacing for Curt Hitch 31367
- It sounds like you might want to use Curt front mount hitch # 31367 on a vehicle it was not designed for. Please note that doing so will void the hitch warranty and can also require major modifications done to the vehicle to get it to fit. This hitch is designed for the 2007 to 2009 Toyota 4Runner, 2007 to 2014 Toyota FJ Cruiser, and 2010 to 2013 Toyota 4Runner Trail Edition only. It will not fit any other vehicles.
The outer holes measures 36.13 inches apart on center. The inner set
view full answer... - Will the Curt Front Hitch for a 2010 Toyota FJ Cruiser Fit with Aftermarket Bumper
- In order to confirm fit of the Curt Front Mount Trailer Hitch Receiver part # 31367 on a 2010 Toyota FJ Cruiser with aftermarket front bumper you'll need to review the installation instructions (attached) and ensure the mounting locations of the trailer hitch do not interfere with the bumper. The trailer hitch manufactures don't do testing on aftermarket parts unfortunately. The hitch weighs around 35 lbs.
view full answer... - Front Hitch Recommendation for 2007 Toyota 4Runner
- For your 2007 Toyota 4Runner we have one front mount hitch, the Curt part # 31367 which is a confirmed fit. We can't recommend trying to install any other hitch on the front of your vehicle.
With a bike rack mounted to the front of the vehicle normally it's not an issue but you have to consider that it might block headlights and turn signals depending on the style of bike and how "see-through" it might be.
view full answer...
Info for these parts were:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Video Edited:
Andrew K
Written by:
Lindsey S
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
John
9/4/2023
Works very well. I use it for mounting bikes in front, mounting a removable winch, and a front basket when I am camping. I had to add a 12 inch extension, the hitch is tucked under quite a bit. This is a very stout set up. No worries for any use.