Lift Supports Specs:
Features:
Install this torsion bar between your truck bed and tailgate to make it easy for you to raise and lower the tailgate on your truck. The EasyLift ensures controlled movement so that you can access your truck bed with just one hand.
Tech Tip:
Product does not work on models with tailgate assist feature.
More Information >Gas Struts Specs:
Features:
If your vehicle's hood keeps closing while you're trying to work on your engine, it's time to change your strut. Replace it with this custom fit gas strut and make your hood operate like new again. Quick, tool-free installation.
More Information >Lift Supports Specs:
Features:
DeeZee's tailgate-lowering system is the safe way to lower your vehicle's heavy tailgate. Expertly designed and built to last, Tailgate Assist controls the drop of your tailgate, preventing injuries and making loading and unloading easier.
More Information >Gas Struts Specs:
Features:
If your vehicle's hood keeps closing while you're trying to work on your engine, it's time to change your strut. Replace it with this custom fit gas strut and make your hood operate like new again. Quick, tool-free installation.
More Information >Videos
for Lift Supports
Help Articles
for Lift Supports
Expert Answers
for Lift Supports
The Air Lift LoadLifter 5000 #AL88200 will work with the Air Lift Air Helper Spring Cradle #AL59DQ on your 2013 Ford F-150. The cradle actually replaces the lower roll plate so the air bag will sit directly in the cradle. I'm not sure…
view full answer...Hey thanks for reaching out, Robert. Your Dexter P-15 model SLR 3,500 lb axle does use the standard bearing combination for a 3,500 lb axle. I was able to confirm this with Dexter. So, you have #L68149 for the inner bearing and #L44649 for the…
view full answer...Hi Robert; the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100 is the correct bearing kit for your axle.
view full answer...You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub…
view full answer...Yes, the Dexter E-Z Flex Suspension Kit #K71-657-00 is the correct kit to upgrade your triple axle trailer which currently utilizes the 13-126 equalizer. Both these are designed for axle spacings 35" apart.
view full answer...Thank you for all the info John, Based on the numbers you provided your pin box has a Rhino bolt pattern with a 21,000 capacity. To find the correct Gen-Y pin box we'll need to check your trailer's pin weight. If the pin weight ranges…
view full answer...Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.
view full answer...The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #GY68GR is roughly 2" shorter than the Lippert 1621 pin box. I've attached a dimensional drawing of #GY68GR for you to check out as well.
view full answer...To flat tow a 2011 to 2013 Jeep Grand Cherokee there are 5 major components needed: base plates, tow bar, safety cables, lighting, and supplemental braking. The base plates are what attach to the front of the Jeep and provide a safe and proper…
view full answer...Ryan, yes the Brophy Slide In Camper Tie-Downs #HSBP should work with your 2017 Chevrolet Silverado 3500, but we have not personally tested them with your truck so you'd have to check the diagram attached and see if they'd work for…
view full answer...Yes, your local installer was correct that you'll need the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TL78ZR and TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear #TL23RR. I do want to note that these will not be compatible…
view full answer...You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
Easy place to shop. Fast delivery and great products. Very happy with my purchase.
Ed
Boynton Beach, FL