RV Jack Pads Specs:
Features:
These 1" thick jack pads serve as a cushion so the metal jack feet on your Class A, fifth wheel, or travel trailer leveling system won't damage your driveway. Heavy-duty rubber resists corrosion and won't crack, even after extended use.
More Information >RV Jack Pads Specs:
Features:
These 1" thick jack pads serve as a cushion so the metal jack feet on your Class A, fifth wheel, or travel trailer leveling system won't damage your driveway. Heavy-duty rubber resists corrosion and won't crack, even after extended use.
More Information >Videos
for RV Jack Pads
Help Articles
for RV Jack Pads
Expert Answers
for RV Jack Pads
If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right…
view full answer...Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector…
view full answer...We may have a grease seal that will work in your application however, my research had conflicting measurements for the Hadco 3122 that you referenced. I contacted my technical contact at Redline to verify that the Redline Grease Seal #1105-100-031…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This…
view full answer...The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is…
view full answer...The closest compatible option for your Dometic DOTR12CB RV microwave's size is the Furrion Standard RV Microwave #FMSN09BL. It measures 19-1/16" W x 13-5/8" H x 15-7/8" D with a 0.9 cu ft capacity.
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.
view full answer...I agree, the bag for the NOCO Boost X Jump Starter #NOC88VR is a nice way to keep everything together but it definitely lacks in the protective department. To keep your Boost X Jump Starter safer you'll want to pick up the EVA…
view full answer...