Expert Review Video:
Trailer Hitch Size:
2 Inch Hitch Opening
Towing Capacity:
2400 Pound Tongue Weight
16000 Pound Towing
Weight Distribution Towing Capacity:
2400 Pound Tongue Weight
17000 Pound Towing
Trailer Wiring:
Features:
...mount, pin and clip sold separately Hitch assembled in the USA Mounting hardware may be imported Specs: Receiver opening: 2" x 2" Rating: Class V Maximum gross trailer weight : 1...
Installation Notes:
No drilling required for installation
Spare tire will need to be lowered or removed temporarily for hitch installation
More Information >Trailer Hitch Size:
2 Inch Hitch Opening
Towing Capacity:
2400 Pound Tongue Weight
16000 Pound Towing
Weight Distribution Towing Capacity:
2400 Pound Tongue Weight
17000 Pound Towing
Trailer Wiring:
Features:
...Mounting hardware may be imported Specs: Receiver opening: 2" x 2" Rating: Class V Maximum gross trailer weight : 16,000 lbs Maximum GTW when used with weight distribution: 17,000 lb...
Installation Notes:
No drilling required for installation
Spare tire will need to be lowered or removed temporarily for hitch installation
Does not fit models with rollpan bumper
Tech Tip:
Hitch does not fit Crew Cab models from 1988 - 1991.
More Information >Videos
for Trailer Hitch
Help Articles
for Trailer Hitch
Expert Answers
for Trailer Hitch
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...I&…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...