Hey Howard, great question but yes the Blue Ox Towed Vehicle Battery Charge Line Wiring Harness #BLU44ER that you referenced does have a diode built into it so that it doesn't backfeed or reverse charge from the towed vehicle to the tow vehicle.…
Hey Hewitt! It looks like the two ARB Base Racks designed for your 2020 Toyota 4Runner are the 72" Long x 51" Wide #ARB37YR and 61" Long x 51" Wide #ARB95GR. The ROAM 95L Rugged Case fits anything that has 80/20 channels. The…
Hello Kayla, I am so glad you wrote in to us! I was able to confirm with MCD Innovations that you will need the MCD Innovations RV Shade Repair Kit - Solo with Steel Brackets - Switch Controlled Motor #MC82YR to replace your current motor…
Hey James, welcome back! The only plug and play wiring harness I have for flat towing is the Curt Custom Tail Light Wiring Kit for Towed Vehicles item #C96JR. This has a 4-way connector that plugs into your motorhome. This plug and play harness…
We've checked with LaSalle Bristol in the past and they do not offer just the replacement cables for their valves so you'd need to go with an all new valve with part #34466N4AB72GMA.
I need two things to help you pick out the correct leaf springs for your trailer. I need to know the axle capacity of your trailer as well as the length from eye to eye without a load on your trailer. With those two pieces of info I can help you pick…
Not at all, Kate! The Rich Solar RV Solar Charging Kit w/ 2 Panels - 12V - 400 Watts #RS97VR is ideal for bus life. It’s a great match for a 200Ah lithium setup, with headroom for adding an inverter or third battery later if you decide to do so. The…
Hey Derek, great question and thanks for stopping by! So mainly between the yellow #SSR-127-54 and the black #SSR-127-47 SumoSpring Solo's is the capacity. The yellow's are going to be for a heavier load application with a 2,800 lb capacity,…
If you have a 3,500 lb AL-KO axle and the brakes are indeed 10 inches, you can use Trailer Hub and Drum Assembly, #AKHD-545-35-K for a standard spindle and #AKHD-545-35-EZ-K for an E-Z lube spindle. For brakes you can use etrailer.com Trailer Brake…
Hello Tom, thanks for reaching out. Yes, you can use the Bulldog Winch Mount #BDW20353 along with a Roadmaster base plate on your 2019 Wrangler Rubicon which is part #RM-521453-5. The picture below shows an example of a similar winch mount installed…
From your description the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-468-469 is exactly what you need. They fit with 10" hubs, are rated for a 3,500 lb axle, and they mount on a 4 bolt brake mounting flange with 2-7/8" spacing on…
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Robert
Bloomington, IL
Rampage Tow Hooks with chrome or black
Built for straightforward recovery setups, Rampage tow hooks keep things simple and solid. Choose chrome or black to match your build, and look for models with 1-3/8" on-center spacing and 3/8" bolt holes to line up with your bumper or bracket.
Yes, they come in chrome and black. Choose the finish you prefer—finish does not change the 1-3/8" on-center spacing or the 3/8 inch hole size. Double-check you're selecting the finish that matches your build.
Match two measurements: 1-3/8" on-center bolt spacing and 3/8 inch bolt holes. Measure your bumper or frame bracket with a ruler or caliper. If either dimension is off, expect a fitment issue when you go to install.
The hole size is 3/8 inch diameter. Verify your hardware and mounting plate accept 3/8" bolts. Test-fit a 3/8" bolt through your bracket to confirm before tightening everything down.
The bolt holes are 1-3/8" on center. Measure center-to-center on your mounting points to confirm. If your spacing is different, the holes may not line up during install. A quick check with a ruler helps avoid a mismatch.
Filters
