Hey Dan, welcome back! I do indeed have a Black Armour mat designed for trailers. It's the Heavy-Duty Trailer Mat item #BA96AR. It measures 5' wide x 7' long and is made of 1/2" thick rubber. This is the only size and option I have…
The Enclosed Trailer Ramp Heavy Duty Spring - Dual, 96" Wide #CB250D96SHD is rated for doors up to 250 lbs. I'm confident your ramp won't weigh more than that unless you've added weight to it beyond the decking.
Hey Rodney! Congrats on your new trailer! If you door weighs 250 lbs or less the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer item #CB250D96SHD will perfectly. You'll just need to trim the shaft down to fit your trailer's…
I do have a couple options that will work for you, but unfortunately there isn't one perfect option that provides everything you are looking for. I have included the options below, along with some of the things that make them work or not work for…
Thank you for the pictures! We do not have an exact replacement but we have something extremely close. It is the LED Trailer Fender Light item #PE89BR. This light measures 3-7/8" long x 1-1/4" tall x 7/8" deep. It is a dual-face LED…
The RV Switch #37213095 doesn't have an option to add a faceplate, but we have an alternative with part #37212625 which comes with a small faceplate with it and carries the same on/on function that you're looking for.
Hey Dan, thanks for reaching out! For your application you'll need the Triple Rocker Switch #37212245 and you'll need to swap out two of the SPST switches with the SPDT RV Switch #37213095 as we don't have any panels that come with the…
It sounds like you have tested your truck with other trailers and your trailer with other trucks and have found the wiring circuits to connect and function correctly. This tends to suggest that there is just an issue between the two specific…
Your photo shows the 7-way trailer wiring setup that we call the RV format. The photo I linked shows an actual trailer plug #A10-7W6 like yours and the circuit arrangement is the same as your photo diagram. For reference, the included article covers…
The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…
Hardware is not included for the Optronics LED Trailer License Plate Light w/ Bracket - 5 Diodes - Clear Lens Item #LPL55CB, but you can make a trip to the local hardware store and pick up some bolts and nuts to secure the license plate, light…
Yes, you can use 4-leaf springs in place of 3 leaf springs. The extra height of an additional leaf is minimal and won't really affect anything on the trailer. Provided that the springs used are replaced in pairs and not just one side of the…
Keep trailer floors protected from stud and track wear with Caliber utility mats. They mount easily with screws, can be cut to fit different spaces, and lay tighter when warmed around 70 degrees before install. Best on a solid surface; over metal mesh they can flex unless you add a base.
Yes, Caliber mats come in different sizes and can be cut to fit when exact dimensions aren't available. If your needed size isn't offered, choose a size with enough coverage and trim to match. Dry-fit the pieces before fastening to confirm the layout.
It can work, but it's not what Caliber flooring is designed for. These mats are meant to sit on a solid surface so they spread the load and stay flat. On mesh, they can flex between openings and feel spongy under weight. Add a solid base like sheet material first to help the flooring perform properly.
You can cut Caliber mats with a knife or a saw. A table saw works, but plastic shavings can build up while cutting, so pause to clear debris. Lay the mats out warm so they're easier to pull tight. Fasten with screws; screws have held them nicely in use.
Yes, Caliber utility mats help protect plywood floors from snowmobile studs and aggressive tracks. They've worked well with ice ripper tracks and eliminated further deck damage. Lay them out first in a warm area around 70 degrees to pull them tight and install correctly. Use screws to secure; screws have held them nicely.
Filters
