The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hi Ron, thanks for reaching out. I completely understand why you're checking that measurement before ordering since if the fins don't reach the slide wall, the seal won't do the job you're expecting. The Rubber Bulb Seal with Fins for…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
To get right seal you'll need to remove a portion of the seal to get the side profile of your current seal. There are multiple types of applications for slide-out seals; Glue On, Peel-N-Stick, Press In, Push On, and Slide-On. There are multiple…
Hey Martin, The only difference I'm seeing between the Replacement Motor #TUS24FR and the Replacement Motor #LC125802 is that the TUS24FR has a 9000 RPM rating while the LC125802 has a 440 RPM rating while under load, which jumps up to 500 RPM…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
RV Slide Out Parts power unit — Lippert Hydraulic Slide-Out Systems
Built to refresh Lippert Hydraulic Slide-Out Systems, these power units make a clean, straightforward swap. Installation is simple and the direct-fit design brings slides back to smooth, quick in-and-out operation. Options include units with a 2-quart reservoir or standalone motors, so you can match your setup and replace only what's needed.
Motor-only replacements are available for certain pumps; confirm the pump assembly number on your label to match the correct motor. Reservoir-only options may not be sold separately, and a 2-quart reservoir typically comes as part of a power unit kit. If wiring differs from your old unit, follow the applicable wiring diagrams.
Start by running the slide in and out 5 times to help purge air. Check for fluid leaks, then inspect the solenoid valve for that slide. Use a hex key to open the valve (clockwise) about 1 turn, then close it back counter-clockwise to help the seal. If it still creeps, the valve or cylinder may need replacement.
Yes, installation can be quick and a direct fit. Several installs were described as an easy replacement that took minutes to about an hour. Verify the mounting and hose locations match your setup, and address any slide out-of-alignment that overloaded the old pump so the new unit isn't strained.
Use AW-32 Hydraulic Fluid. Do not use an automatic transmission fluid. Check your system label to confirm the spec before filling, then top off with the same fluid type already in the reservoir to avoid mixing.
Filters
