Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hey Jason! For your 2026 Ford F-450 I recommend the Redarc Tow-Pro Liberty Brake Controller #RED67CR. This comes with a custom wiring harness that will plug into the factory brake controller port under the dash. The Liberty is simple, reliable, and…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Hey Robert & Carol, That part number comes back to a custom order piece. Is this the channel on the side of your RV that the fabric from your awning slots into, like part #LC715216? If you'd like to email me some pictures I'd be happy to…
Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?
While we don't carry a hinge with the exact leaf setup as what you have pictured, the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black #LC95VR is still a viable replacement option. Since the leaf configuration is slightly…
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI
RV Door Parts with Keyed Alike Convenience
Streamline your setup with keyed alike RV door parts so multiple locks open with the same key. Great for entry and baggage doors or replacement cylinders, they make installs straightforward on many rigs, though some fits may need small mods. For the best match, verify your door thickness, latch cutout size, and door hand orientation.
Installation can be quick, often around 10-15 minutes, but some doors need small mods. Verify the kit includes hardware to attach both sides of the latch. Ensure the lock cylinder is fully seated so the tumbler doesn't pull out. If your old plates are rusty, use the new door and frame plates included with some kits.
Yes, slam latches are available Keyed Alike and will fit a 1-1/4" thick door. If there isn't a mounting plate on the door, add one to complete the install. Confirm your door thickness before ordering and reuse existing hardware if it matches, or use the included hardware if provided.
Yes, you can get locks and replacement cylinders keyed alike so one key works across locks. Ordering a specific key number can let an existing key fit a new lock, and new keys can work existing cylinders when matched. If replacing just cylinders, measure cylinder length and confirm they are removable on your latch.
Match the door thickness and the cutout size first. Entry latch kits note fits 1-1/4" to 1-1/2" doors and cutouts from 2-1/2" to 3" wide x 3-1/2" to 4" tall. Some replacements are slightly larger or smaller than the old lock, so dry-fit and hold the handle square while tightening to prevent a gap. Start the two screws by the latch and deadbolt to keep it level.
Filters
