Truck Bed Mats Specs:
Features:
...span>customized fit and simple, do-it-yourself installation mean that you get a smooth, snug liner for your truck bed. You can remove and reinstall factory tie-downs through the BedRug or just cut small slits so...
Installation Notes:
Trimming or cutting is required for trucks equipped with Cargo Management Rails in the truck bed
More Information >Truck Bed Mats Specs:
Features:
...span>customized fit and simple, do-it-yourself installation give you a smooth, snug mat for the bottom of your vehicle's bed. The BedRug installs quickly over your bare truck bed or spray-on liner usi...
More Information >Truck Bed Mats Specs:
Features:
...span>customized fit and simple, do-it-yourself installation give you a smooth, snug mat for the bottom of your vehicle's bed. The BedRug installs quickly over your bare truck bed or spray-on liner usi...
More Information >Truck Bed Mats Specs:
Features:
...BedRug mat creates flat surface with a soft carpet feel for your truck bed and tailgate Integrated guard hinge covers tailgate gap 3/4" Thick padded floor for impact prote...
More Information >Truck Bed Mats Specs:
Features:
BedTred Impact mat upgrades your vehicle bed with a 3/4" thick layer of polypropylene and a tough thermoplastic top. Provides a flat surface, prevents skidding loads, and cushions your cargo. Covers your bed floor, tailgate, and tailgate gap.
More Information >Truck Bed Mats Specs:
Features:
BedTred Impact mat upgrades your vehicle bed with a 3/4" thick layer of polypropylene and a tough thermoplastic top. Provides a flat surface, prevents skidding loads, and cushions your cargo. Covers your bed floor, tailgate, and tailgate gap.
More Information >Truck Bed Mats Specs:
Features:
...BedRug mat creates flat surface with a soft carpet feel for your truck bed and tailgate Integrated guard hinge covers tailgate gap 3/4" Thick padded floor for impact prote...
More Information >Videos
for Truck Bed Mats
Help Articles
for Truck Bed Mats
Expert Answers
for Truck Bed Mats
I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…
view full answer...The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...For a 2023 GMC Canyon we currently offer the BedRug Custom Full Truck Bed Liner #BR76ZR, which will fully cover the bed, bedrails, bulkhead, and tailgate.…
view full answer...Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't…
view full answer...The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole…
view full answer...The Rear Hanger for 2-1/2" Wide Slipper Springs -…
view full answer...It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below…
view full answer...I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons…
view full answer...The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system…
view full answer...