# 1
K-Source Universal Towing Mirror - Clip On - Convex Mirror - Qty 1
After years of replacing mirrors from other sources I purchased a pair of these. There fantastic, plenty of adjustments. Got covid on vacation, really sick and did not properly install mirror. Not broken but scratched badly from asphalt at 55 mph. Purchased a replacement, scratched one is my spare.
These mirrors are good, but not great. I bought these because nothing else fits my 2004 Ford Expedition. They allow me to see around my trailer much better than the factory mirrors, but the have a slight vibration driving down the road. They also make a very noticeable noise from the wind going between the factory mirror and this product. Finally, one of the straps came off when I tightened it a bit too much, but didn't break. The picture below was done in humor (I took my trailer through a drive through, thought it was really funny, and had to take a picture. The picture is a good shot of the mirrors.)
# 2
K-Source Universal Dual Lens Towing Mirrors - Clip On - Pair
These worked great on my wife's Yukon. Installation instructions were clear and direct. They held up very well traveling 75 mph down the interstate; No jostling around or coming loose. I loved the additional two mirrors. Having the three total different angles while pulling a trailer was extremely helpful. Would highly recommend this setup.
Tried 3 other styles of tow mirrors for my 2019 Jeep Grand Cherokee but nothing would fit properly until I bought these. Love the ratchet style clamping system. Fit perfectly. Great product for my SUV.
# 3
K-Source Universal Towing Mirrors - Clip On - Convex Mirror - Qty 2
After reading lots of reviews on several mirrors, I decided to buy the K-Source Universal Towing Mirrors. Oh how I wish my truck could use the ones that slip over the existing mirrors! I was prepared for a fight, based on reviews, and boy did I get one! I truly needed a third hand when figuring out how to attach these. I was bound and determined that I could do this on my own. No mirrors were going to defeat me! I did ask my husband to come look at them. He started to help but I shewed him away. After a lot of words that don’t normally come out of my mouth and a few tears, the first one was on! Then I had to go do it again in the other side! I’m pretty sure the neighbors heard me yelling. But I persisted! Lo and behold, this 67 year old Grammy did it! It was clear they would not stay on by themselves, so I grabbed a couple of bungee cords and wrapped them around the housing and they aren’t going anywhere. I have left them on my truck. No way I’m going thru that every time we return from camping. I will take them off at the end of camping season. Delivery was really fast. I was disappointed that one box was brand new and the other was smashed and taped, an obvious return. I would have been very unhappy if there was a piece missing or if something was wrong since this was my first purchase with etrailer. Overall, the mirrors work, they do not shake and I find I don’t use the truck mirrors now. Very happy with my purchase.
Fitted on 2024 Toyota Tundra SR5 CrewMax Cab w/ Stock Mirrors No vibration issues with either mirror. Turned left and right side clip on mirrors vertical so the did not overlap truck mirrors. Right side no problem with attachment and was able to adjust truck mirror. Could also see father back along right side of a 24’ travel trailer than just looking in truck mirror. Don’t expect to see behind on right side any vehicles tucked up close. Left side mirror attachment had to be modified so I could adjust truck mirror without interfering with clip on mirror lower L “hooks”. I put a rubber blocks under the lower L hooks so they were low enough to get under truck mirror glass yet still clamp to truck mirror housing. A picture tells the story. 7,000 km/4,200 miles later and neither mirror has loosened or moved. No vibration or distortion. Yes, I ran 2 zip ties as safety “chains” from the back straps to truck mirror arm just in case, they’re barely snug. I recommend these.
# 4
CIPA Universal Fit Dual-View Towing Mirror - Clip-On
Pros: Very easy to install. Will fit on almost anything. Cons: Bit of a challenge to adjust the in/out tilt on fixed mirror housings. Would like a little more height, but it's OK. This is a good solution for the casual user like me. Installation is painless. If you need more control over height or tilt, this is not for you.
I bought the trailer mirrors for my Jeep Grand Cherokee to pull my pull behind trailer. See pictures. The mirrors attach easily and securely and shake very little when driving. I need them mostly when backing up and I can see where the trailer tires are going. The mirrors do not adjust easily but when you do they stay in place. What I especially like is the size of the mirrors and having two independent mirrors.
# 5
CIPA Universal Dual Lens Towing Mirrors - Clip On - Qty 2
Unable to tighten mirror clamps enough to eliminate mirror from shaking, preventing clear image while driving.
The mirrors were just what I needed and work well on my Toyota highlander.
# 6
CIPA Universal Fit Towing Mirror - Clamp On - Adjustable Length - Steel
Mirrors work exactly as intended, greatly improving rear vision when towing our pontoon behind our 2014 Tacoma. Store nicely in the compartment under the rear seat.
Excellent product. Easy to put on. Took them off, put them in my camper storage. Next trip out, when I put them on, I did not even need to adjust them! The mirrors are slight contour and slight magnification, which makes them easy to see. There is virtually NO vibration during travel. (I have had others that shimmied so bad you could not see a thing.) I flip my driver side mirror in frequently to check my mail box, so it is not very stiff. So I ran a small bungee from the clamp to the grill under my hood. Did this for both sides. My driver side flipped in when traveling at interstate speeds, so I put a second bungee on it. Fixed the problem. Allen bolts at top of clamp are rusting after 2nd use. All in all though, I am very pleased with this product and it is well worth the money spent. It is the only product I could find to properly fit my 2011 Toyota Tacoma, because it clamps on the mirror frame and does not rest on my truck mirrors. Great Product!
# 7
CIPA Universal Towing Mirrors - Clip On - Qty 2
The company was fast and gave lots of updates for shipping. Once i received product my concerns were met. The straps are BARELY long enough to connect around my mirror. Once it is straped properly the tension on straps pulls them right out of the retaining clip. I ordered these because i have a 11 silverado just like what was in the product pictures. Save your money and get something else because theres no way these will make it down the highway they will barely stay on just sitting here. Kinda disappointed because i bout these for our first camping trip this weekend but these will not work. Seems like a good company just crappy product.
Thank you for the easy shopping experience and delivery.
# 8
CIPA Universal Towing Mirror - Clip On - Qty 1
The good: inexpensive; decent quality materials The bad: doesn't hold it position very well during extensive or high speed travel - you have to readjust at nearly every stop for gas on a trip. Conclusion: It is worth the money due to its fair price.
Purchased a pair for our 2017 Jeep Grand Cherokee towing a nuCamp 400 from FL to AK and back. Three months and around 16k miles. Pros - other than an adjustment the second day, I never had to adjust the tension straps again. They were easy to mount and did not interfere with our mirrors folding inward. They weathered three months on the road without issue though I was beginning to worry about the straps becoming brittle. I noticed this once I removed them. Had I kept them, I would have used some silicon to rejuvenate the rubber. Cons - the only con is they shake. They shake to the point that sometimes I couldn't distinguish what exactly was behind me. I knew there was a vehicle, but the distortion from the vibration prohibited me from getting a clear view of exactly what was behind us. Impressions - they worked for our trip but I knew I would want something else for our next long trip, so we invested in a Furrion Reviewing Camera.
# 9
CIPA Universal Towing Mirrors - Clamp On - Qty 2
So far, so good. I received the CIPA mirrors today and immediately installed them. Installation instructions are straight forward. I took a test drive of about 15 miles; there was no noticeable shake or rattle and the mounts did not loosen. As with factory curbside mirrors, objects are closer than they appear with the CIPA mirrors, too. Our first trip towing is a couple weeks from now. I will update my review after the trip.
The view is excellent. The mirrors do not vibrate. In speeds over 50mph, the tube would turn inside the clamps and the mirrors would turn upward, making them useless. Solution: I cut off a finger from a nitrile rubber glove and pushed it over the tube. Now the mirrors stay put.
# 10
K-Source Universal Towing Mirrors - Clip On - Flat Mirror - Qty 2
I went right away to try them on my truck. I have a 24 Denali ultimate 1500 Denali and I have a couple of cameras on my side mirrors. The straps are easy to maneuver around the cameras to avoid issues there. Good snug fit I have not taken it out yet to test these in real road conditions but so far so good.
Worked well and as expected. Still can't see as far behind the camper as I would like on the passenger side. Strap them on tight. They shook very litte but some, not enough to be bothersome. Later,I did find them less expensive elsewhere, oh well. Straping them on is tricky to not cover the cameras underneath the truck mirrors. Truthfully I use the camera on the back of the camper along with these mirrors and get additional views from the Chevy cameras as well. I'm not a truck driver and only pull the camper on occasion so I need all the "eyes" I can get especially driving through Nashville and Atlanta.
# 11
CIPA Custom Towing Mirror - Slip On - Driver Side
They are very easy to install and remove when parked for extended periods. Costumer service was very helpful with getting me the correct marrows.
Great product! I use them on all my trailers as well as my travel trailer. This is actually me second set...the first got destroyed by a hit n run and i could not live without them!
# 12
CIPA Universal Fit Towing Mirrors - Clip-On - Qty 2
Haven’t had a chance to use these but did put them on my truck to get them adjusted. Easy to install and look like they will give me good coverage.
The Universal fit towing Mirrors-THis is easy to put on and off and gives great visibility when towing our boat
# 13
CIPA Custom Towing Mirrors - Slip On - Driver Side and Passenger Side
Excellent Product…Easy to Install and the instructions were very easy to understand… These Mirrors fit perfectly on my 2016 Ram 2500 SuperCrew 4x4 Truck
So far this might do the trick . A bit concerned on stability after long trip .. we shall see in time !! The passenger side is not as tight as drivers .. again time will tell .
# 14
CIPA Custom Towing Mirror - Slip On - Driver Side
The mirrors help me tow our Lance trailer safely. The adjustable mirrors benefited with a touch of dry lubricant on the joint inside the housing. Emily at etrailer was very helpful!
First set had a factory defect. The hole for the tension knob was not threaded. Replacement sent was also a defect, the mirror panel swivel was un-adjustable. Spend the extra money and get the correct OEM ones for your vehicle.
# 15
Longview Custom Towing Mirrors - Slip On - Driver and Passenger Side
The mirrors were extremely easy and the fit is perfect. These look almost like a factory option installation. All lamp and cameras are exposed and not blocked. The individual mirrors are easily adjustable. Great product! Very pleased.
These mirrors helped tremendously when towing my Micro Minnie travel trailer versus stock mirrors on my GMC SIERRA 1500. The extended mirrors enabled to better determine when it was safe to move back into my lane after passing a vehicle and allowed me to see better the vehicles behind trailer. Although there was an occasional slight vibration in the passenger side mirror, it did not disrupt the usability of the mirrors. The towing mirrors took only a minute or two to install and fit perfectly on the stock mirrors. Adjusting them properly takes a little more time and is easier when a second person helps. I am extremely pleased with this purchase!
Mount: CIPA Universal Fit Towing Mirror on a 2017 Acura MDX
Speaker 1: Today on our 2017 Acura MDX, we're gonna be doing a test fit on the Cipa Universal Bar Clamp-On Towing Mirror. It's available in a quantity of one with part number CM11980. You can also pick it up as a pair with part number CM11980-2. It offers us a wide field of view. It's gonna allow us to safely and easily change lanes, pass, park, or even back up while towing a trailer or camper. As you can see, I'm visible in the towing mirror, but not the factory mirror.
How to Install the K-Source Universal Dual Lens Towing Mirrors on a 2017 Acura MDX
Speaker 1: Today on our 2017 Acura MDX we're going be doing a test fit on the K-Source Dual Lens Clip On Towing Mirror. It's available in a pair with part number KS3990. It offers us a wide field of view. It's gonna allow us to safely and easily change lanes, pass, park, or even back up while towing a trailer or camper. As you can see, I'm visible in the towing mirror, but not the factory mirror.Now our towing mirror has two mirrors. The larger one is gonna give us an accurate reading of what's behind us, while the smaller one is gonna be our spot mirror.
Set up: CIPA Universal Towing Mirror on a 2017 Acura MDX
Speaker 1: Today on our 2017 Acura MDX, we're going to be doing a test fit on the Cipa clip-on towing mirror. It's available in a quantity of one with part number 7070. You can also get it as a pair with part number 7070-2.It offers us a wide field of view. It's going to allow us to safely and easily change lanes, pass, park or even back up while towing a trailer or camper. As you can see, I'm visible in the towing mirror, but not a factory mirror. Now, if I take a few steps towards my trailer, as you can see, there's no blind spot by the way we have it set up, but this is the view you get with just your factory mirror.The four tabs are not going to interfere with the operation or movement of our factory mirror, and we can even still fold it in.The mirror itself is adjustable 360 degrees so if you'd like to have at that horizontal position, you have that option.
Beginner’s Guide to Installing the K-Source Universal Towing Mirror on a 2013 Acura MDX
Speaker 1: Today on our 2013 Acura MDX, we're going to be doing a test fit on the Ksource Universal Clip-on towing mirrors.It's available in a quantity of one with part number KS3891. You can also pick it up as a pair, with part number KS3891-2.It offers us a wide field of view. It's going to allow us to safely and easily change lanes, pass, park, or even back up while towing a trailer or camper. As you can see, I'm visible in the towing mirror, but not the factory mirror. Now if I take a few step in towards my trailer, you can see there's no blind-spot by the way we have it set up, but right here is the view you get with just your factory mirror.The mirror itself can be adjusted to most angles. We've got our up and down, diagonal and side to side.
Mount: K-Source Universal Dual Lens Towing Mirrors on a 2013 Acura MDX
Speaker 1: Today on our 2013 Acura MDX, we're going to be doing a test fit on a K-Source Universal Dual Lens Clip-On Towing Mirror, part number KS3990. It's sold as a pair. It offers us a wide field of view. It's going to allow us to safely and easily change lanes, pass, park, or even back up while towing a trailer or camper. As you can see, I'm visible in the towing mirror, but not the factory mirror. Now, our towing mirror is two mirrors.
Setting up the CIPA Universal Fit Towing Mirror on your 2013 Acura MDX
Speaker 1: Today on our 2013 Acura MDX, we're going to be doing a test fit on the Cipa Universal Bar Clamp On Towing Mirror. It's available in a quantity of one, with part number CM11980. You could also pick it up as a pair, with part number CM11980-2.It offers us a wide field of view. It's going to allow us to safely and easily change lanes, pass, park, or even back up while towing a trailer or a camper. As you can see, I'm visible in the towing mirror, but not the factory mirror. Now, if I take a few steps in towards my trailer, as you can see, there's no blind spot by the way we have it set up, but right here is the view you get with just your factory mirror.The mirror itself can be rotated 360 degrees, so if you'd like to turn it to that horizontal position for a different view, you have that option.
2013 Acura MDX CIPA Universal Fit Dual-View Towing Mirror: Complete Installation
Speaker 1: Today on our 2013 Acura MDX, we're going to be doing a test fit on the CIPA Dual-View Clip-On Towing Mirror. It's available in a quantity of one with part number 11953, you could also pick it up as a pair with part number 11953-2.It offers us a wide field of view, it's going to allow us to safely and easily change lanes, pass, park or even back up while towing a trailer or camper. As you can see, I'm visible in the towing mirror but not the factory mirror. Now our towing mirror has two mirrors, the larger one is going to give us an accurate reading of what's behind us, while the smaller one is going to be our spot mirror, it's going to help us during changing lanes and passing. Now, if I take a few steps in towards my trailer, as you can see there's not blind spot by the way we have it set up, but right here's the view you get with just your factory mirror.Both mirrors can be adjusted to most angles, we got our up and down, diagonal, and side-to-side. The four tabs are not going to interfere with the operation or movement of our factory mirror and we can even still fold it in.
DIY 2013 Acura MDX Installation for the CIPA Universal Towing Mirror
Speaker 1: Today, on our 2013 Acura MDX, we're gonna be doing a test fit on the Cipa Clip-on Towing Mirror. It's available in a quantity of one with part number 7070. You can also pick it up as a pair, with part number 7070-2. It offers us a wide stable view. It's gonna allow us to safely easily change lanes, pass, park or even backup when towing a trailer or camper. As you can see, I'm visible in the towing mirror but not the factory mirror.
What our customers are saying:
"You folks are fast. Thank you very much."