# 1
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
this hitch is great. i needed a longer ball mount to give me more room between my trailer jack and spare tire on the tail gate of my jeep wrangler. it is very hard to find a extra long ball mount. i found etrailer has them and a lot of other fine products.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
Install took a little more time than planned, did not lower the muffler. The four bolts from left to right, number two and four were threaded. 2015 Rubicon, had to get the number two bolt started first and then the others worked fine. Start the threaded bolts first. Electrical hookup easy. Have not towed yet, don't expect problems.
# 4
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
i HAVE PURCHASED SEVERAL PRODUCTS FROM ETRAILER. HAVE ALWAYS HAD QUICK DELIVERY OF THE PRODUCT I ORDERED. PRODUCTS WORK WELL AND ARE EXCELLENT QUALITY. SERVICE, INFORMATION AND ASSISTANCE FROM ETRAILER IS TOP NOTCH, THAT IS WHY i HAVE BEEN A REPEAT CUSTOMER FOR A LONG TIME.
Very well made ball mount. Etrailer is a great company to do business with, huge inventory and shipping second to none. Buy American! Ron
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Perfect Fit! 07-12 Jeep Wrangler JK with 3.5" lift. This was the exact product to get the trailer back on level. Great service and fast shipping.
# 6
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
GOOD QUALITY
# 7
Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
The D-26 is just the right length for my 2008 Jeep Wrangler. The 32in spare tire doesn't get in the way of the hitch even with 3/4" rise. yay
# 8
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
This was a gift, the recipient was very excited to receive it, she will now be able to tow the ski boat behind her jeep, she couldn't before due to the spare tire interfering with her previous hitch.
Just what I needed to add clearance for towing our 1962 Shasta Astroflyte that has a bunk that hangs out over the tongue.
# 9
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Excellent product - very strong and secure! Does not, however, fit my 2016 Jeep Wrangler Unlimited. It is about 3.5 inches too short to clear the spare, and about that much too tall to go under the spare.
Hitch was as expected... appreciate the extra communication by etrailer.
# 10
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 11
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
Everything here to tow in a easy kit.
There were some UPS delivery issues, damaged in shipment. But, etrailer.com jumped right on sending out another shipment after it was apparent that UPS would not complete the delivery. The installation took longer, maybe 1-1/2 hours, because I did not have all my tools ready and I was working on the concrete floor in the dark to outside with a portable shop light. Everything fit well and it looks great. The 2" drop ball mount was the perfect height for my 2019 Toyota Highlander Hybrid. I love the look of the Curt black insert that makes the hitch looks like it belongs on the car, nothing embarrassing at all. Anything negative? Maybe. The flat plate was a little difficult to hook onto with the UHaul safety chains on a 5x8 trailer. That's hardly a negative, though, and I wouldn't have spent more on another brand choice because of this. Happy happy!
# 12
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The D-26 is just the right length for my 2008 Jeep Wrangler. The 32in spare tire doesn't get in the way of the hitch even with 3/4" rise. yay
Love it. It's on jeep wrangler and now I can hook up my trailer and crank up the tongue stand without hitting my spare tire cover
# 13
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
Excellent quality. Made in USA
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."