# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
GOOD QUALITY
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
EXACT AND FAST
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
this hitch is great. i needed a longer ball mount to give me more room between my trailer jack and spare tire on the tail gate of my jeep wrangler. it is very hard to find a extra long ball mount. i found etrailer has them and a lot of other fine products.
# 4
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
This was a gift, the recipient was very excited to receive it, she will now be able to tow the ski boat behind her jeep, she couldn't before due to the spare tire interfering with her previous hitch.
Just what I needed to add clearance for towing our 1962 Shasta Astroflyte that has a bunk that hangs out over the tongue.
# 5
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
EXACT AND FAST
The D-26 is just the right length for my 2008 Jeep Wrangler. The 32in spare tire doesn't get in the way of the hitch even with 3/4" rise. yay
# 6
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Excellent quality. Ordering was easy and delivery was fast. Looks like the perfect amount of drop for my jeep to keep trailers level.
Perfect Fit! 07-12 Jeep Wrangler JK with 3.5" lift. This was the exact product to get the trailer back on level. Great service and fast shipping.
# 7
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Excellent product - very strong and secure! Does not, however, fit my 2016 Jeep Wrangler Unlimited. It is about 3.5 inches too short to clear the spare, and about that much too tall to go under the spare.
Hitch was as expected... appreciate the extra communication by etrailer.
# 8
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 9
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
EXACT AND FAST
i HAVE PURCHASED SEVERAL PRODUCTS FROM ETRAILER. HAVE ALWAYS HAD QUICK DELIVERY OF THE PRODUCT I ORDERED. PRODUCTS WORK WELL AND ARE EXCELLENT QUALITY. SERVICE, INFORMATION AND ASSISTANCE FROM ETRAILER IS TOP NOTCH, THAT IS WHY i HAVE BEEN A REPEAT CUSTOMER FOR A LONG TIME.
# 10
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
EXACT AND FAST
Excellent quality. Made in USA
# 11
Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
EXACT AND FAST
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
# 12
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
What our customers are saying:
"Thank you! I enjoyed shopping your site."