# 1
Rhino-Rack Nautic SUP or Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.
Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.
# 2
Thule Hull-A-Port Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
only gave a 3 star because i have not used wating for summer
This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.
# 3
Rhino-Rack Crossbar Pads w/ Tie-Downs - Universal - 21-1/2" Long - Qty 2
I love this rack! I don't think I'll ever take it off my car. Cool and functional. I've used it for my snowboard in the winter and my surfboard and camping gear in the summer.
The product very well made.. I have owned for a year now.. stays in place.. protects my paddle board
# 4
Yakima JayLow Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.
Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.
# 5
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
I bought these folding-J racks to accommodate two kayaks on my ‘15 Honda Accord. I mount the sit-on upside down on the Rhino Rack roof rack and the touring sit-in on the folding J-racks. With it having folding capability, I’m able to set at proper angle to accommodate both yaks. When traveling home with the new sit-in, I had to pull over on the side of highway to re-tighten the straps since a strong side wind caused it to move. I over tightened because that caused indentation on the bottom of the yak from the cross bars. That was remedied by putting in the sun and they pulled out, per seller’s advice. Yeah, freaked me out a bit being my first yak! I use bonnet straps on the ends now, too. Lesson learned. The folding J-rack prevents any possibility of indentation on the bottom of the sit-in yak. These folding J-racks are well made and I recommend them.
First experience with purchasing from etrailer. Absolutely felt that my order was personalized which is a nice touch. The Rhino Rack S512 folding JStyle Kayak holders arrived boxed impeccably with no damage whatsoever and the price was great! Fantastic first time experience. Looking forward to using them. Thank you.
# 6
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.
# 7
Thule Compass Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
Wry disappointed in such an expensive rack and kayak carrier. It is extremely difficult to reach the carrier to place two kayaks. We are very uncomfortable transporting the kayaks for longer and highway travel. I would not recommend these to others. We likely will purchase something other in the future. I’d rather put the kayak in a car or pickup truck that they would fit in.
We bought this Kayak rack for my mom to put on her 2016 Jeep Grand Cherokee so her and my dad could haul their kayaks easier. The mounting hardware was a little tricky at first but once we figured it out, it wasn't bad at all. It holds the kayaks in place nicely. Had no issues with them getting loose or moving around. Seems to be built well and they're very happy with it so far.
# 8
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
Awesome product
I installed these as soon as I got them and I’ve got to say, there are some extra holes for screws that are a tad misleading and the pieces that secure it to the cross bars don’t seem super secure. For reference, I do have Rhino Rack’s vortex crossbars so this should fit snug. The rubber tops were tough to get into place and I am worried they’ll snap when I go to remove my rack but Rhino Rack has yet to fail me with their products so I bet it’ll work out great!
# 9
etrailer Kayak Carrier w/ Tie-Downs - J-Style - Folding - Clamp On
Brought home a new kayak yesterday using this J cradle for the first time. Easy to set up and load. Two complaints: not impressed with the strap buckles - had to tie knots to secure. And the 3-inch bolts weren’t long enough to easily attach the cradle to my Rhino Rack crossbars, so I had to replace them. Also got my finger pinched pretty good adjusting the cradle knobs - my fault for not being more careful, but just saying …
Great product for the price - The cradles were very easy to mount (and lay flat once folded). The videos were helpful in showing how to set the straps in the most efficient way. I test-drove my car today with my fishing kayak on top on a 80-mile round trip (a mix of freeway, country road and dirt tracks). The kayak was perfectly still, no particular wind noise and I was able to muscle to kayak up the roof and take it down on my own (it's a 52 lbs boat). I really recommend that product and I'm glad I went for J-Style cradles!
# 10
Swagman Tajo Wall Mounted Kayak Rack
Ordering was very easy and I really like the fact that I had reviews from others "with pictures". That helped me tremendously. The items came within 2 days (WOW). I didn't expect that. They are exactly like show and I will be installing them today. I don't expect any problems. (update after installation) I have now installed and I would have given a rating of Excellent, but I did not because of 1 problem I had. The screws that come with the product are soooo cheap that they all began to strip out as I installed them. And yes I was using the right Phillips head bit and I even had my drill set to stop if it hit resistance. The Phillips head has very small cross threads. If you look at the pics you'll see what I mean. This Phillips head is too small of threads for a larger 2" screw like this. As such, I ended up having to spend $20 on a screw extraction product (Grabit drill extraction) to get 1 of them out. I since replaced all these crappy screws with ones with better heads that are made of actual metal, not paper-mache that looks like metal. By the way, the Grabit screw extraction tool works great... Now that they're up, they look great and do perform exactly like I expected. I would definitely recommend these...
Works well except the screws need to be stainless steel
# 11
Rhino-Rack Nautic Stack Kayak Roof Rack w/ Tie-Downs - Post Style - Folding - Universal Mount
've previously used the Yakima Kayak Stacker (old style), which worked fine but I always worried the straps would slip off the hook at the top while I was loading boats. They also didn't fold down, so had to be removed after use unless you wanted to look odd and cause a whistle while you drove down the road. They didn't have a universal attachment option, requiring adapters depending on the style and make of your crossbars. More recently I got the Thule "The Stacker", which is a superior solution. You thread the strap through a closed loop at the top, so you don't worry about straps slipping off while you're loading boats. They fold down after use and have a universal style attachment that fits around most styles and makes of crossbars. Good stuff. I really like the straps that come with these, as there is a rubber cover that slips over the metal cam buckle to protect your car's paint while you're tossing the strap over your boats to strap everything in. In order to shuttle our boats for river trips, we needed stackers to fit on both our cars, so it was time for another set. I had never heard of Rhino Rack before, but the lower price than Thile caught my eye, so I read about them and decided to give them a try. The Rhino Rack Nautical Stack used a closed loop at the top, which I liked better than the Yakima or Malone options, and came with the hardware necessary to install them into the C-channel of my Malone aero crossbars, which I wanted to try. I remember that with the Malone stacker, you had to buy the C-channel mount hardware separately. I really like the Rhino Rack Nautical Stack. They are a single post design, unlike the loop style of the Thule "The Stacker". I don't know if this cuts down on vortex drag, but it definitely saves you a couple horizontal inches up where the boats stack. The Rhino Rack Nautical Stack has textured rubber strips on either side of the post, which I believe is intended to cut down on vortex drag, but is also quite helpful in that boats tend to slip much less when you're just leaning them up against the post as you load up before you strap them. That's smart. The Rhino Rack Nautical Stack feels really solid. The mechanism for folding them down and locking them upright is easy to use and feels solid. Installation instructions were good. I tried to install into the C-channels without removing the rubber tubing in my Malone aero crossbars, but couldn't get the little squares to slide into the slots with the rubber tubing in place, so had to cut the tubing, slide the Nautical Stacks into place, then cut down some of the tubing I had removed and replace it in the remaining unfilled crossbar slot. That's not a knock on the Nautical Stack; just a tip in case you're trying to do the same kind of install I did. The one area in which I was less impressed was the tie-down straps that come with this kit. The metal cam buckles have no covering at all, so I'll probably still use my old Yakima and Thule straps instead and use these as backups. But overall, I think these are going to work at least as well, if not better, than the Thule option, and for quite a bit less money.
So much better than the 'C-shape' kayak holders. These things allow you to fit inside a garage, and add up to four kayaks. Very easy to use.
# 12
SUP and Surfboard Pads for SeaSucker Monkey Bars - 19-1/2" Long - Qty 2
They were perfect. We had lost a set and had a difficult time locally finding them.
Quality product, does what is supposed to do
# 13
Thule Stacker Kayak Roof Rack w/ Tie-Downs - Post Style - Folding - Clamp On
We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.
My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.
# 14
Rhino-Rack Nautic Roof Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.
This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!
# 15
Inno Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
Decent tie-downs but a bit of work to tie everything down and get the kayak settled, especially with a heavier kayak around 50 pounds and 12 feet long. The rubber pads do their job a little too well in that case!
I purchased a car rack system as well as the kayak carrier and it arrived in only two days! It was easy to put on and fits my 2013 Hyundai Tucson Limited perfectly. I picked up my new kayak the next day and mad it home with no issue what so ever. I am very satisfied with this product.
# 16
Thule SUP Shuttle Stand-Up Paddleboard Carrier with Tie-Downs - Roof Mount - 2 Boards
Very easy to install on roof rack. Just be careful not to lose one of the rubber pieces that help protect your board. They can easily fall off of the rope when tying your board to the rack.
With a little help from youtube, this was one of the easiest things I've ever assembled! LOVE my new SUP rack!!
# 17
Thule Hullavator Pro Kayak Roof Rack and Lift Assist w/ Tie-Downs - Saddle Style - Universal Mount
Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)
2018 Ram 2500, wanted a way to travel with 2 sit on top kayaks, With my wife and i in our late 60's it was taking a LONG tome to get the kayaks on the roof of the bed cover. With these i can do it with a short stool. Also carrying the kayaks upside down keeps the top cleaner and stops the water from getting trapped in the kayak (and raining down on me when I unload them).
# 18
Swagman Contour Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.
Loved the racks, seem very durable. Only downside was that the groove made for the crossbeam was quite a bit smaller than my crossbeams, but they still secured down great. You'd have to have a pretty funky set-up for these racks to not work on your vehicle. Having all the straps/tie-downs included was awesome too. Reccomend!
# 19
Thule SUP Taxi XT Stand-Up Paddleboard Carrier - Roof Mount - 2 Boards
I love my Rack it came when promised and etrailer was great believe me I will be going back to them for anything else I need I am giving them a well deserved 5 stars
The only thing better than the quality of the product was the quality of etrailer’s customer care. I had to return the Thule SUP Taxi because it was too difficult for me to tighten the straps with my arthritic hands, these wonderful folks were completely obliging, helpful and courteous!
# 20
Rhino-Rack Nautic 580 Side Loading Kayak Roof Rack w/ Tie-Downs - Saddle Style - Channel Mount
These are great. I had trouble finding a system I really liked but then on a trip one of our friends had these and loved them. They are simple, secure and low profile. I use them with 18’ sea kayaks. The pads flex to fit the hulls just right, the boats are super secure, no wondering around and you don’t have to strangle them into the saddles. I was worried maybe the boats wouldn’t slide easily onto them when loading but it’s no problem. One note, the slugs were just a shade too big to fit in my older TracRac slot. It took just a little work with the grinder, no big deal. Very happy.
Easily adjustable. Very happy with them after 1 year. I carry 10ft and a 12ft kayaks.
What our customers are saying:
"Outstanding service and followup. Thank you"