Most Popular Class I for 2015 Dodge Journey

Its was the right drop for the height of my truck, and works as well and maybe even better than my last hitch. I think it might be do to the covert a ball I am using with it which lets me tow different trailer with different size ball's.

Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!

Very good deal!!! And the quality is superb.

Nice kit for the money meets my trailer pulling needs.

This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.

Click to Enlarge

Well made, quality product.

Needed a longer unit to accept a bike carrier.

Click to Enlarge

Quality product. I needed a longer mount for my side by side and this will work well.

Hello The hitch works great as viewed in the enclosed pictures. If inverted it hits the bumper, of my Dodge 2500. The section that goes into the receiver is about 1/2" too short and hits the bumper. I have not tried it on my other vehicle to see if this is a problem. Kind Regards Leon D

Click to Enlarge

A VERY nice piece that will set your mind at ease. Easy to adjust height. The ONLY thing I wish is there was an option to have different sized ball combinations. I mainly use 2" and NEVER use a 2 5/16"(or whatever the larger size is) and would prefer to have a 1 7/8" on the other side.

Click to Enlarge

I had to flip this upside down and put a hitch ball on this to get it to work with my Dodge Journey and my camper. It's held up without issue for a half-dozen camper pulls. I wish the paint hadn't already started flaking off at the receiver end, but that's to be expected when you connect metal to metal. The other parts of this haven't started flaking yet after a year so hopefully it continues to hold up.

Really well built

Still haven't towed anything with it yet but it seems very solid. I do think it will rattle some in the receiver because it is loose in my 2" receiver on my 2019 F150.

This hitch has worked out great for me over the last year. It’s very heavy duty and easy to adjust. I’ve hauled a 9,000 lb boat, long-distance on numerous occasions without issue. I also haul a landscape trailer on a daily basis weighing over 5,000lbs and haven’t had a single issue. Great hitch that was significantly cheaper than others and is very high quality. I’ve recommended it to several people and I wouldn’t hesitate to buy again. The only thing I would like to have now in a hitch is a tongue weight gauge, but it isn’t necessary.

Click to Enlarge

Good product.

Ball mount works perfect with my hitch. Great product!

Very solid. The only thing I dislike is that the balls started to spot rust after leaving it in the hitch over some days in the winter. I imagine it was due to salt exposure from the road.

Solid product! Built well. The arm itself is a solid piece (not hollow). Seems to be able to withstand years and years of abuse. I ordered this product and a few other items, and for some reason my order was sent to the wrong address. The customer service at etrailer.com were OUTSTANDING!! They first called for a follow up to see if I got my package, and then immediately got in touch with the shipping company to see where my parts were at. Long story short, they sent me out ANOTHER parts order immediately while an investigation was going on with the first order. These guys are AMAZING, I have never had a company do that in my years of ordering online send out another replacement of my order just to make sure that I was a satisfied customer. I will ALWAYS get parts that I need from a company that helps out their customers in that way. Thanks eTrailer!!

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

Click to Enlarge

Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.

Great Product! After installing a Curt (C11184) Hitch on my '08 BMW 135i convertible, I needed a drawbar and ball. I really liked the elegant design and one piece simplicity that this one has. It is very sturdy and the dimension measurements were accurate. The whole reason I got it was to trailer my new (old) wood boat home from the barn I found it in. Once the hitch was on and the (56146KIT) Wiring kit was installed. This drawbar slid right in. Thanks to the accurate measurements the trailer sat at the perfect height the first time.

Click to Enlarge

Click to Enlarge

works great

Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.

This 13" drawbar keeps the tailgate off the trailer jack. Being that long also keeps it I storage immediately after I disconnect the trailer. No need for a locking pin.

Solid build. Slid right in and is solid as a rock.

Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys

Its was the right drop for the height of my truck, and works as well and maybe even better than my last hitch. I think it might be do to the covert a ball I am using with it which lets me tow different trailer with different size ball's.

All of the items arrived on time and not damaged in any way. Excellent quality products.

I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!

Click to Enlarge

Drawbar looks great and will be using in next two days. Thanks!

Purchased for a Dodge Journey with vertical mount hitch. Waited 5 months to get one from Chrysler and finally gave up found this one online. Sturdy design and does what I need it to. My only complaint is there is no recessed slot for the hitch ball to screw in tightly.

Tried to get this from the Dodge who put on the hitch. After six weeks of waiting I called you and got it in two days. Thanks.

Solid build. Slid right in and is solid as a rock.

Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

Click to Enlarge

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

Click to Enlarge

I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!

I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.

Excellent hitch! Needed the extended length as our bumper isn't notched for towing. With a tongue weight of 1100#, there aren't many hitches that offer the extension with weight rating. This one fits perfect! Thanks

Click to Enlarge

This hitch is solid - literally! Super heavy duty.