# 1
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
This longer ball mount was what i needed to give me more room to open the back door on my FJ when towing a trailer. Have to take it all out for a test drive soon. Also added a side mount swivel jack to give me some more ground clearance. The picture only shows the jack.
As always etrailer nailed it. Fit my 2010 FJ perfectly, easy install, has seen heavy usage hauling motorcycles to the woods/track and nary a peep out of it. Can't beat etrailer price, quality or service.
# 3
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
As always etrailer nailed it. Fit my 2010 FJ perfectly, easy install, has seen heavy usage hauling motorcycles to the woods/track and nary a peep out of it. Can't beat etrailer price, quality or service.
This longer ball mount was what i needed to give me more room to open the back door on my FJ when towing a trailer. Have to take it all out for a test drive soon. Also added a side mount swivel jack to give me some more ground clearance. The picture only shows the jack.
# 4
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Needed to extend my hitch a little farther from the vehicle and this one seems to fit the bill. I tow an AT Chaser offroad trailer behind an FJ Cruiser and need a hitch bar that can take some abuse, and I'm hoping this one stands up.
Solid! great coating and finish
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!
I have a 2012 GMC Sierra HD with a 12" suspension lift. I recently purchased a ball mount hitch with 8" inch drop for our 36' RV trailer and it worked great. It took 3 days for the hitch to get to me. Great service from e-trailer.
# 6
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 7
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 8
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 9
Lock N Roll Articulating Trailer Hitch for 2" Receivers - Vehicle Side - 11,000 lbs
Both connecting lock n roll products are a great addition to my project roof top tent, utility, kayak mounted, Solar energy equipped overland adventure trailer. Not only has my travel range increased due to this go anywhere upgrade, but my trailer security and its value has increased also. I am a very happy customer. So.e fab work may be necessary.
I had to drill a new hole about an inch further up. The shaft gets a little larger towards the connection keeping the shaft from going in enough for the holes to completely line up. Worked fine after that.
# 10
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 11
Convert-A-Ball Cushioned Multi-Hitch Clevis and Pintle Hook Combo w/ 3 Balls - 2" Hitches - 10K
No problems with the hitch- makes it easy to switch between trailers! I have no complaints!
Very good product and I would have given it a 5 star rating but there is one critical flaw that is quickly remedied. When using the pintle hitch, the pressure exerted on pin while pulling a load can cause the pin to turn, thereby popping out the keeper pin. This happened twice and it was a good thing that I had the hitch positioned so that the pintle pin was installed going down allowing gravity to hold the pin in place even when the keeper pin fell out. I have since changed out this style of keeper pin with a cinch pin that can spin 360 degrees inside the 2" tube and no pressure is exerted on it by the load being pulled. If I were designing this from new, I would make it so that the draw pin on the pintle had a square shoulder much like a carriage bolt so that it can't turn thereby eliminating pressure on the keeper pin. Other than that it is a great product.
# 12
Flash Self-Locking, Aluminum Ball Mount - 6" Drop, 5" Rise - 10,000 lbs
Excellent hitch. I like that it is made from one piece of solid aluminum and so much easier to lock and unlock. No more fumbling around under the bumper trying to unlock the hitch pin.
Just what I'd hoped for. Extremely light-weight and easy to install/remove. Perfect mount for my new Jeep Cherokee!
# 13
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
Works great. Needed the drop to tow a utility trailer at level.
I purchased the AMSC10 because I needed a 10" drop hitch to tow my lowboy enclosed trailer with my lifted Toyota Tundra. I tried several other types of hitches with this towing combo and I was always disappointed. Mostly because of the fit/sloppiness of the ball mount into the receiver. This would cause a lot of noise and the feeling of the trailer "bucking" while hitting bumps and such. The other hitches that I tried were those cool aluminum ones, both a fixed one and an adjustable one. Although they were pretty, both left me very disappointed. The shipping for this hitch from Etrailer was fast and efficient. I received emails informing me of my order status throughout the whole process. Upon receiving my AMSC10, I tested it out and found it to be a much nicer fit into the receiver. Once I hooked up to the trailer and began to tow, the difference was extremely noticeable. This hitch is quiet, it doesn't buck, and in fact, comparatively, you wouldn't even know the trailer was behind you unless you looked. I am actually really excited about towing with this hitch. I know it sounds goofy, because it is, but it makes the task so much more pleasurable with the cushion ball mount. I'm already thinking about buying the 8" drop for my normal trailers.
# 14
Curt Solid 2-Ball Mount for 2" Hitches - 2" and 2-5/16" Balls - 10K - Black
Very solid.. great product !!!
This thing is very solid and heavy duty; it weighs in at 16.8 pounds. I haven't pulled with it yet, but I believe it's exactly what I needed to pull the two trailers I need to pull (2" ball, and 2 5/16" ball).
# 15
B&W Heavy-Duty Ball Mount - 1" Rise, 2" Drop - 8-1/2" Long - 16,000 lbs
I have used B&W hitches for many years and I've been very happy with the quality of their products. etrailer makes it easy to shop for these hitches since the B&W site is terrible. I was able to find the correct size and all dimensions were listed clearly. Thanks again!
heavy solid fits thanks
# 16
Pro Series Tri-Ball Mount for 2" Hitches - 1-7/8", 2", 2-5/16" Balls - Black
Not only did I get the parts I needed at a great price. They were delivered they day after I ordered them. Great communication from my salesman. I will definitely be a return customer.
Heavy duty hitch. Well built and welds are fine.
# 17
Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs
Shipping was a mess, lost the first one in the mail somewhere because no one thought a 50# hitch would punch through cardboard. It is working as expected, but does not seem to be a true 2" drop.
Easy ordering, fast shipping and a quality product. I can't believe how much this Brophy Ball Mount Hitch weighs! Incredible.
# 18
Draw-Tite Ball Mount for 2" Hitch - 7" Rise, 8" Drop - 9-1/2" Long - 12,000 lbs
Heavy Duty Drop Down Hitch no problem pulling a 10,000# trailer
It fits perfect on my f350 diesel, super heavy duty. I'll be using it for towing my car tilt bed trailer.
# 19
Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 2" Drop - 15,000 lbs
Nice and heavy and does what it is supposed too
I tried twice to get this hitch and ball from [online vendor]. Twice the shipment was lost and I had to get a refund. Shipment from etrailer is right the first time and arrived quickly. Plus, since the ball is already torqued on the ball mount, I don't need to by a large socket.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."