# 1
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
After one year of using our swagman, we are very happy. We own RAM 1500 with ram boxes and mounted the swagman at the back end of the bed. We mounted the skewers on the bottom side of the bar, to mount the bar upside down. This let the end brackets mount perfectly on the side walls just in front of the end gate. Our bikes when mounted face the rear. Works great!
This rack fits and functions perfectly in my 2018 Ram Rebel. I have the Ram Box cargo management system and I set it up as recommended and it was great! Then I reversed it, as some other folks have done, and mounted it near the tailgate just off the bed floor. This allows me to load and unload from the ground and it keeps the bikes below the cab roof line. So wherever the truck can go the bikes can go without snagging on anything. Went out for a varied terrain test drive and it didn't budge. Package came clean and undamaged with a completely functional inventory of parts. Every part was machined properly and the lock works as well as the release button. No problems at all with anything! Just rotated the fork mounts 90 degrees for the low mounting position and it was done. Etrailer really came through on this one! I will continue to do business with this company!
# 2
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
Very easy to assemble, even easier if you read the directions first and look closely at the diagram to install the tire loop brackets correctly. Excellent solid mounting for the bikes and the rack. Especially like the screw-in hitch pin. Locks it up tight. Even better, it is easy to load the bikes. Much easier than my old one. I can load/unload my bike is less than 30 seconds, my older carrier took several minutes untying straps, loosening a top clamp plate, putting parts away. This one folds up quite well for storage and is lighter too. Great carrier.
Product has been used a few times, very easy to set up and adjust, works well and securely holds two bicycles in place. I would highly recommend this rack for anyone with one or two bikes. also note it folds up when not used. I would purchase from this company again. unit was well packaged and company did exactly as promised...
# 3
Softride Shuttle Pad Tailgate Pad for Full-Size Trucks - Up to 6 Bikes - 61" Wide
The fit for a 2014 Ram was spot on, no issue with the wide style tailgate top and the access flap for the tailgate handle lined up perfectly. Material is durable and easy to clean, the only thing holding it from a 5 stars is if it had the padded dividers on top to keep the bikes separated. But for the price, the fit and finish was exceptional, great value !!!
Doesn't seem to fit the 2024 Chevrolet High Country tailgate as the straps aren't long enough. Also, the padding doesn't go far enough down the outside of the tailgate. Could be because I have the factory bed protection which covers the top of the tailgate.
# 4
Swagman XTC4 Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
Rack is very sturdy and heavy duty. Instructions were terrible. Locking hitch pin would not thread correctly and ended up damaging it. Thankfully the threads on rack were fine and I was able to use the non-locking threaded pin. Would like a replacement locking pin ASAP
For the price, it's a good-quality, sturdy bike rack. I have used it about 5-7 times with no issues. I only used it for one adult and two kids' bikes, but I am sure it can handle four bikes as advertised. It's great that the rack folds upwards when it's not required.
# 5
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
Using this as a front mounted bike rack since I'm hauling a camper in the back. Fits perfectly on my ram 1500. Feels very sturdy so I don't have to worry about anything coming loose. This plus a front mount hitch receiver costs less than a swing arm hitch attachment by itself so I would recommend this combo over a swing arm in the back for anyone looking to bring bikes with their truck camper or fifth wheel.
Easy to use Would have liked it to have a 5/8s hitch pin hole
# 6
Swagman Upright Bike Rack for 1 Bike - Roof Rack Crossbars - Frame Mount
Great product for the price. Pretty easy to set up. Only issue I have is my mountain bike, which is an XL frame with 27 inch wheels, is pushing the limits of the base. Wish this rack was just 4-5 inches longer that way you have the perfect overlap amount in the middle without pushing the current frame to the limits. With that said it does hold my bike just have to find the sweet spot. But this fits my son’s youth bike perfectly!
As always with products I buy from e-Trailer, this item is exactly as advertised and works perfectly. Easy assembly, I bought 2 but only installed one until I check the fit with my rooftop carrier.
# 7
Inno Velo Gripper Bike Rack for Truck Beds - Clamp On
Installs easily, and holds tight even on rough back roads. Adjust easy to fit my bike exactly. I will purchase another one for my other truck.
Works As described and well-built. Clever design. Very easy to install would definitely recommend it to a friend.
# 8
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
Good people to deal with,good service,very helpful with any questions,very fast delivery, highly recommended
Fantastic bike rack. Switch it between a Honda Ridgeline and a Subaru Outback Wilderness and it works perfectly. Accidentally lost the locking pin that secures the rack to the trailer hitch and when I inquired with Kurt about ordering a replacement lock keyed to match the locking cables on the rack and the Kuat rep sent one to me for free. (I removed the rack and left the lock sitting on my car bumper. Later that day I drove off and lost the lock on the highway).
# 9
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Extremely well made hitch rack. Fantastic service from etrailer.com
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
# 10
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
Had bought three of these a year ago and placed it on a cut 2" x 4" for three bikes. All three bikes (2 MTB and 1 Road) now easily fit the 5'7" bed of my Ram 1500. No worries with the quick release and no more stress taking the whole family to the trails. So glad I got these.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 11
Swagman Chinook Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
My order arrived from eTrailer in two days and the container was in great shape. I received great assistance from Julie, she is very professional and provided great info about my prospective purchase. The Swagman Chinook is very well constructed, heavy duty and heavy. The basic assembly took about 45 minutes with more time making adjustments to fit my bikes. It is very stable when connected to my 2015 Ram 1500 Crew Cab, I noticed very minimal wobble or shake on a test drive after I connected it. I would definitely recommend it to others.
Works for my fat tire bike. Once it's set up, it's easy to install and remove. I had to cut out some of the plastic cladding on the underside of my bumper on my 2014 Subaru Outback. Good value. I've had no issues.
# 12
Hollywood Racks TRS SE Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Very helpful and knowledgeable. Quick service and delivery got exactly what I ordered thank you
I purchased the 3500 model for a 2-inch hitch for my 2004 Toyota 4Runner. I've had it for a month now and it has worked well. It took just over an hour to assemble it and the instructions for the most part were easy to follow although it would behoove you to read it through once before you even start putting parts together. The rack has pretty much stayed on the vehicle for the past month and I use it two to three times a week to commute to work. The bike is on the rack for the 26 miles roundtrip to the ferry terminal and it hasn't given me any problems. Service and prompt delivery was much appreciated. I even noted that the link for installation instructions was broken and Anna responded immediately and I now see that it is there! One thing that my photos will show is that if you have a flat handlebar bike in the position closest to the vehicle the hatch may not fully open because the handlebar will prevent it. Not an issue with me since I use it for commuting and don't need to access the hatch. I think the price is worth it since I wanted this type of rack and it was difficult to find anything with this quality and features in the range. Four stars only because I've only had it for only a month so not sure how well it will hold up in the months to come. I also much appreciate the videos of the rack on the etrailer website. Thanks, etrailer! Arthur
# 13
Curt 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting
I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.
Have used mine several times in the past 2 years on the back of a ‘21 Honda Pilot and a ‘19 Ram 1500 Classic. I really like that the platform will tilt downward allowing the Pilot rear hatch to open with no interference. The tailgate on the Ram doesnt open fully even with the platform tilted downward, but that is a Ram problem & not a Curt problem. Was well worth the money.
# 14
Kuat NV 2.0 Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
This bike rack has worked well for our family of 4. It allows us to safely and securely carry all 4 bikes through the mountains of Colorado with our Hallmark Milner truck camper. Strong and durable rack that barely moves when driving. etrailer's customer service was outstanding. The rack was initially delayed and after one phone call to check status a warehouse manager quickly solved a minor issue and got the rack shipped. etrailer was fantastic in managing this transaction with extremely limited staffing. etrailer is the first place I check for anything recreation as I've never had anything but stellar service.
Excellent rack, a year later still in great condition. No movement at hitch when driving like other racks. Love the extra bar to work on bike in parking lot. Cracked a part on the rack when backing up accidentally hit it, I called the company and they immediately sent out new part no questions asked and rack is like new. Easy to access the drop and raise bar even with bikes on .A note that with larger mountain bikes only three really fit on the four rack without adjusting handle bars. Thanks to etrailer for stocking a great product and providing excellent post purchase service
# 15
Curt Clamp-On Bike Rack for 3 Bikes - 2" Ball Mounts
It broke, (the tension handle snapped off) the first time I used it, which was 45-60 days after I purchased it. Nether Curt nor etrailer provided any warranty relief since it was 30 days post sale. It's in a landfill now, and I won't buy from either company again.
A frustrating experience. I bought this bike rack hoping that it would be a really good fit for our needs. We went on a road trip where we were going to camp as we went. Towing a small trailer I mounted the rack on the back of our Honda Element. I had trouble getting the bikes (two) to ride high enough off the road. On the first day of the trip I had to stop at a bike shop to replace a tire that had melted as it had been rubbing on the tailpipe along the way. I also had a major challenge connecting the rubber straps because they were so stiff. Now, I am getting older and just don't have the strength I had in my younger days, but still I just think they are too stiff (I wasn't the only one that had trouble getting these things on...we finally got them on between me, my wife, and the bike tech). It ended up being a frustrating trip. We ended up not using the bikes due to the difficulty we had adjusting the rack. Sorry for a poor review. It is partially my own fault because I could have chosen a different rack in the first place.
# 16
Swagman Trailhead Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches - Tilting
This is a very solid product! I have used it for over a year now and love it! I have had up to 3 bikes on this without a problem and have traveled over 8 hours in the car one way with absolutely no issues. Many other bike racks like this one that I see on other cars look unstable this is not unstable in anyway. I did have to file some of the paint off of the rack to get it to fit in my 1 and 1/4" hitch but once that was done it has been perfect. I also bought the locking hitch bolt which is awesome too.
Well built and good quality. So glad I can haul bikes easier with our Honda Pilot now!
How to Set Up Your Thule EasyFold XT Bike Rack for 2 Electric Bikes on a 2009 Dodge Ram Pickup
Adam: Hi everyone. Adam at Etrailer.com. Today we're going to be taking a look at the Thule EasyFold XT on our 2009 Dodge Ram 1500.So basically this is going to be probably one of the more unique bike racks that you can get. One being it does have some wheels so you can wheel it up into place. Pull this lever down. This is definitely going to be one that is easier than most to put in.
Does it Fit? Testing the Thule Hitching Post Pro Bike Rack for 4 Bikes on a 2009 Dodge Ram Pickup
Today on our 2009 Dodge Ram 1500 series quad cab pickup we're going to be test fitting the Thule Hitching Post Pro folding and tilting 4-bike rack. That's going to be part number TH934XTR. We're going to go ahead and slide the shank of the bike rack into the receiver tube of the 2" hitch until the pinholes line up. Then we're going to hand tighten the bolt once those pins are aligned. Once that's hand tightened we can finish tightening with a wrench. We can give it a wiggle just to make sure that it's in place, and then we're going to do some measurements. We're going to start by measuring our ground clearance.
Fit Check: Testing Hollywood Racks Traveler Bike Rack for 4 Bikes on a 2009 Dodge Ram Pickup
Today on our 2009 Dodge Ram 1500 Series Quad Cab pickup we're going to be test fitting the Hollywood Rack, the 4-bike rack. That's HR8500 is the part number. This is a tilting rack, and it's also designed for 1 1/4 as well as 2 inch hitches. We've got a 2 inch hitch here today, so we're going to start by feeding the shank of the bike rack into the receiver tube of the hitch, until those pin holes are aligned. Once they are, you can begin threading in your anti-rattle bolt by hand. .. Once that's as far as you can get it by hand you can finish that off with your socket wrench.
Saris Axis Hitch Bike Racks Review - 2009 Dodge Ram Pickup
Today on our 2009 Dodge Ram Pickup 1500 Series Quad Cab, we'll be test fitting the Saris Axis 2 Bike Rack part number SA832. We'll go ahead and begin by inserting our shank into the 2 inch receiver here until our pin hole lines up. Go ahead and hand tighten that there. This is an anti rattle bolt, it's going to relieve any excess wobble or anything like that for our ride. We'll go ahead and take some measurements here. Now for ground clearance we are looking at about 17 inches and to the nearest point from the bumper about 6 1/2 inches and overall length we've added about 11 inches. I'll go ahead and show you the tilt feature.
Hollywood Racks Traveler Hitch Bike Racks Review - 2009 Dodge Ram Pickup HR9200
Today on our 2009 Dodge Ram 1500 quad cab we will be test fitting the Hollywood Racks Traveler 5-bike rack, part number HR9200. Go ahead and start by inserting our shank into our 2" receiver here until our pinholes line up. Once we get those lined up we'll go ahead and insert our anti-rattle bolt. We can hand tighten that. We'll take our socket wrench and finish tightening the rest of the way. This is going to remove any excess wobbling or any rattling that the bike rack may have.
Saris Freedom SuperClamp Hitch Bike Racks Review - 2009 Dodge Ram Pickup
Today on our 2009 Dodge RAM pickup 1500 Series Quad Cab, we will be test fitting our Saris Freedom Superclamp platform style 2-bike rack, part number SA 4025. Let's go ahead and insert the shank into the receiver here, until our pinholes line up. Once our pinholes have lined up, go ahead and insert our anti-rattle bolt, and start hand tightening. I'll come in with our wrench and finish tightening that down. That's going to keep the bike rack from shaking back and forth, or any wobble, or anything like that. We'll go ahead and put on our provided lock, until that clicks into place. Let's go ahead and take some measurements.
Softride Dura Parallelogram Hitch Bike Racks Review - 2009 Dodge Ram Pickup
Today, on our 2009 1500 Series Dodge Ram Quad Cab Pick-Up, we're going to be test-fitting the Softride Dura Parallelogram. This is a four-bike tilting rack, and it is part number SR26247. It's designed for 1 1/4 as well as 2-inch hitches. We've got a 2-inch hitch here today. We're going to begin by threading the shank or fitting the shank of the bike rack into the receiver tube of the hitch until the pinholes are aligned. There are multiple pinholes on this shank, and we're going to go with the pinhole that allows the bike rack to sit furthest away from the vehicle, which will be suitable for the most clearance of our tailgate. Once that's in place, we're going to thread our anti-rattle bolt into the pinhole by hand.
Fit Verified: Saris Freedom Bike Rack for 4 Bikes on a 2009 Dodge Ram Pickup
Today on our 2009 Dodge Ram 1500 Series Quad Cab, we're going to be test fitting the Saris Freedom. This is a platform style 4 bike, hitch mounted bike rack, Part Number SA4414B. Our truck has a 2 inch by 2 inch class 33 hitch on it. We are going to getting a test fit by sliding our bike rack directly into the receiver tube of our hitch. We're going to push this in here until we see that our pin holes line up with one another. Once we get that lined up we can take our anti-rattle bolt, place it through, we're just going to go ahead and get it hand tight.
Saris Bike Porter Hitch Bike Racks Review - 2009 Dodge Ram Pickup
Speaker 2: Today on our 2009 Dodge Ram 1500 Series Pickup Quad Cab, we will be test fitting the Saris Bike Porter 4 Bike Rack part number SA404B. We are going to begin by inserting the shank into the receiver here until our pin holes line up. Once those are line up, you should be able to hand tighten. Once we got that hand tight, we go ahead and use our socket wrench. By tightening this, this is going to relieve any wobble, excess wobble that the bike rack may have. Once we got that, we go ahead and put our clip in the other side here.
Softride Hang5 Hitch Bike Rack Review - 2009 Dodge Ram Pickup
Today on our 2009 Dodge Ram 1500 we'll be test fitting the Softride Hang5 Hitch Mounted 5 Bike Rack, Part Number SR26496. We'll begin our test fit by sliding in the shank of the mast into the opening of the hitch. After lining up our pin holes, we'll thread our anti-rattle bolt through the pin holes and then tighten it down using a wrench. We'll then go ahead and slide the arms of the bike rack into the upper portion of the mast. You'll know when the arms have been fully secured when you hear an audible click. We'll go ahead and go over a few clearance measurements to see how the two fit together.
What our customers are saying:
"I ordered a trailer hitch and a bike rack carrier the order was shipped with in three days. To put the hitch on only took about 30 mins. only had to drill two 1/2 holes. fit like a glove."