# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
It is what it is. Well made, and accepts a 1" shank on whatever size ball you choose.
Great company to work with.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
It is what it is. Well made, and accepts a 1" shank on whatever size ball you choose.
Changed this item out as wanted a lover receiver. Return was super easy! Great customer service!
# 3
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
I recently purchased this hitch and related wiring accessories from etrailer for my 05 Hyundai Tucson. Following the included installation instructions I found the hitch easy to install. Total install time including the wiring adapter was approximately 1.5 hours without rushing.
# 4
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 5
Adjustable Ball Mount for 2" Hitches - 9" Rise to 10-1/4" Drop - 5,000 lbs
This ball mount gives me the adjustment I needed on my Dodge Grand Caravan when I rent different trailers. The part that goes into the hitch does have a little play but it is no worse than my current fixed height ball mount. The adjustable ball mount with the 2 pins also has about a 1/8" play so be ready for that if you buy this adjustable ball mount. That would be the only improvement I think they could make in the future is to have the pins a little larger and/or the holes a little smaller to reduce the play. However, this might just be the way these need to be designed at this price point based on the research I have done with other adjustable hitches.
Unit worked, but the fit between the 2.5" adapter and the hitch was loose. It caused the trailer to rock back and forth with every application of the brakes. Had to make shims to stop unit from clanking. Felt like if length of attaching piece was longer it would had helped. Attached picture to help illustrate.
# 6
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
Works great. Needed the drop to tow a utility trailer at level.
As always etrailer has the best products, best information and customer service, plus fast shipping! Thank you again!
# 7
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 8
Brophy Ball Mount - 5" Rise, 6" Drop - 16" Long - Aluminum - 8,000 lbs
Perfect for my Tahoe. I have a 2019 Tahoe LS 4x4 with the max tow package. The receiver is mounted higher than than on the truck it replaced. Six inches of drop appears to be just about right for my boat trailer.
I bought a new trailer that came with a tongue mounted jack stand. The problem was the hand crank was to close my truck and prevented me from lowering my tailgate while the trailer was connected, by about a 1/2 inch. I had a standard steel 6 inch drop Reece ball mount. This one has more weight capacity, but is half the weight of the older ball mount. It added just enough distance from the truck I can put the tailgate down!
# 9
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 10
Curt Dual Length Ball Mount for 2" Hitches - 1" Rise, 2-3/8" Drop - 7,500 lbs
Quality product. I needed a longer mount for my side by side and this will work well.
# 11
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Every thing looks like it will do the job I need it to do .
Love this product. Thank you for you support.
# 12
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
What our customers are saying:
"I received this order yesterday. Thanks for the outstanding service. I appreciate it! Thanks, Alex"