Draw-Tite trailer hitch # 24871 for the 2012 Chrysler 200 is rated for 2,000 pounds gross trailer weight and 200 pounds tongue weight. Provided that the trailer is within that capacity as well as the capacity of the vehicle then it will be able to tow it.
The recommended ball mount for this hitch is # 3594. For a compatible 1-7/8 inch ball use # 19256 or for a 2 inch use # 19258.
And for a trailer wiring harness you can use # C56211 to add a 4-Way flat connector to the rear of the vehicle. view full answer...
Your 2013 Chrysler 200 has the transverse Pentastar 3.6 liter which Kat's recommends their heater part # KH11814. The cartridge location you need to use is right behind the engine block on the driver side. So the side of the engine that faces the firewall and all the way on the driver side. view full answer...
Sounds like the carriage bolt hasn't slid all the way down into the carriage bolt block and that is why it is just turning. You have to pull the bolt all the way through the block so that the square shoulders of the bolt slides into the square hole of the block. view full answer...
I did check with Roadmaster and the Roadmaster EZ4 Base Plate Kit # RM-52297-4 that you referenced is only a fit for the sedan version of the Chrysler 200. It will not work with the 200 convertible.
At this time there is not a custom base plate kit available for your 2012 Chrysler 200 Convertible.
You may be able to go with a universal base plate kit like the Blue Ox # BX88230. Most bumpers do need to be reinforced or modified for proper installation, as the brackets need to mount to... view full answer...
There is not a hitch mounting application for a tent if that is what you are referring to. We have some tents that attach to the back of SUV's and truck beds, but nothing for a 2015 Chrysler 200. My recommendation is to either use a separate tent like the Rightline Pop-Up Tent - Sleeps 2 - 90" x 72" x 42" # RL110995 or the Let's Go Aero ArcHaus Tent Shelter - 10' Long x 6' Wide x 6-1/2' Tall # SAR024.
The rooftop option like the Yakima SkyRise is not an option for your vehicle because... view full answer...
There is a trailer hitch receiver for your 2015 Chrysler 200, and for that I highly recommend the Draw-Tite Trailer Hitch Receiver # 24919.
This is the best option for your Chrysler because of Draw-Tite's reputation for quality and its easy installation. If you C56242, Draw-Tite Drawbar # 3593, and 1-7/8" Hitch Ball # 19256 or 2" Hitch Ball # 19258.
I have added a link to a video install for you to check out as well on a 2015 Chrysler 200 of the Draw-Tite Trailer Hitch Receiver # 24919. view full answer...
I included an image for the instructions for Draw-Tite trailer hitch # 24919. As you can see the receiver will be basically the only part visible. This is because it is welded to the bottom of the cross tube which is hidden.
If you plan on doing some towing with the hitch on your 2015 Chrysler 200 then the correct ball mount to use is # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # C56242.
If you want to use the hitch for an accessory... view full answer...
Currently our Curt Drawbar # C45028 has the most rise available for a 1-1/4" Class I receiver like that you would have on your 2015 Chrysler 200. The rise is 5-3/8" from the receiver.
To get slightly closer to your 6" rise you can use a Curt Class I Drawbar # C45025 with a Curt RockerBall Shock Absorbing 2" Hitch Ball # C94CR. The ball mount has a rise of 5" and the RockerBall sits 1-1/2" higher than a traditional 2" ball. As long as your trailer accepts a 2" ball this would give you... view full answer...
I do have a solution for you but the problem is that the trailer hitches for the 2015 Chrysler 200 are all rated for 200 pounds tongue weight. The combined weight of the scooter and a carrier would exceed that 200 pound capacity. The best option is to put the scooter on a small trailer (there are some out there made specifically for mobility scooters). This is the safest option and will also reduce the stress put on the vehicle.
You would still need a trailer hitch such as # C11403 and... view full answer...
For the 2012 Chrysler 200 with a bare roof, I would install the Inno Roof Rack which uses part numbers # INB127, # INSUT, and # INK600. This is the most affordable roof rack for this vehicle and would work well with a kayak carrier such as etrailer J-Style Kayak Carrier # e98878. This J-style kayak carrier offers a simple tool-free installation and comes with all the straps necessary for securing your kayak. I attached a couple demonstration videos for you to check out. view full answer...
The most popular hitch for a 2013 Chrysler 200 Sedan or Convertible is the Curt Class I trailer hitch # C11133.
I wouldn't recommended using a cargo carrier to carry an electric wheelchair with a Class I hitch because your maximum tongue weight is 200 pounds. Based on the wheelchair carriers weighing roughly 90 pounds and electric wheelchairs around 200 pounds it will exceed the 200 pound maximum tongue weight.
The best option to carry the electric wheelchair is by a trailer because... view full answer...
The Curt hitch part # C11133 that you referenced has been confirmed to fit the Sedan and Coupe models of the 2013 Chrysler 200 so it should work well for you.
I attached an install video for you to check out as well.
The Curt hitch comes with the correct ball mount, hitch pin, and clip. For a ball you can use # 19256 for 1-7/8 inch diameter or # 19258 for a 2 inch diameter.
For trailer wiring, use Vehicle Wiring Harness # C56211. I have included a link to the installation instructions... view full answer...
I have a hitch that is designed as a fit for your 2014 Chrysler 200, but the one you mentioned is not so it would not fit.
Instead you would want the part # C11133 which is a confirmed fit. view full answer...
To be able to transport your Permobil C300 electric wheelchair with your 2013 Chrysler 200 convertible, I recommend installing a trailer hitch and wiring harness on your vehicle and using a mobility chair trailer.
The trailer hitch I recommend for you is the Draw-Tite Class I Receiver Hitch # 24871. The recommended drawbar for this hitch is # 3594. A hitch ball compatible with the trailer coupler will be needed as well. You can use # 19256 for a 1-7/8 inch diameter ball, or # 19258 for... view full answer...
Yes, the Thule Force XT XXL Rooftop Cargo Box # TH6359B referenced in your question will fit and work great with the Thule AeroBlade Load Bars that are on your 2015 Chrysler 200.
This is an excellent, aerodynamic cargo box that features a carrying capacity of 22 cubic feet. Its dual-side-opening lid will let you load and unload gear from either side of your Chrysler 200 and 2 Thule locks are included to protect your cargo. view full answer...
Yes, you are correct. Curt hitch # C11133 is a fit for your 2014 Chrysler 200. The recommended ball mount is # C45522 and for a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258.
For trailer wiring you can use # C56211.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.
Curt... view full answer...
There is an underbody panel that will need to be trimmed or removed to install la hitch on a 2015 Chrysler 200 but no bumper fascia trimming.
I recommend Draw-Tite trailer hitch # 24919. It is the most popular option for your 200. I have linked the instructions for you to view.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited... view full answer...
With the Curt Trailer Hitch Receiver # C11133 on your 2013 Chrysler 200, Curt recommends using one of the following ball mounts.
First is the Curt Class II Drawbar # C45522 with either a 1-7/8" Ball # C40001 or 2" Ball # C40018. Or you can choose one of their Euro Style Ball Mounts with a 1-7/8" # C45591 or 2" # C45592 ball. Whichever you choose you will need a Curt Hitch Pin and Clip # F-4 to secure it in your receiver.
You will also need a Vehicle Wiring Harness # C56211 to control... view full answer...
The Swagman XTC-2 2-Bike Platform Rack part # S64670 is a great option for a 2013 Chrysler 200 Convertible when used with the Curt Trailer Hitch Receiver part # C11133. In regards to the convertible action, the bike rack should not interfere while folded flat with the upright laid down to the side. view full answer...
Yes, trailer hitch # 24919 will fit your 2015 Chrysler 200 S. I have linked a video showing an example installation for you.
The appropriate ball mount is # 3593 if you plan on towing. For a 1-7/8 inch ball I recommend # 19256 and for a 2 inch ball I recommend # 19258. And for trailer wiring I recommend # C56242 to add a 4-Way flat to the rear of the vehicle.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is... view full answer...
Go To Results