The height from the top of the top mounting bracket on the Jif Marine Fishing Rod Holder # JIF82FR to the top of the rod holder is approximately 1-7/8". view full answer...
From the bottom of the rod holders on the Yakima TopWater Rooftop Fishing Rod Carrier # Y04088 to the bottom on the case is going to vary since there are different sized ridges. From the holder down to the lowest ridge is approximately 5". Fromthe holder down to the center flat ridge it's approximately 4-3/4". From the holder down to the two rounded ridges it's approximately 4". view full answer...
The 70 Series Fishing Rod Holder # CE53672A weighs just over 1lb.
The rest of the dimensions are Length: 9", Tube inner diameter: 1-5/8", Tube outer diameter: 2", Mounting flange dimensions: 44-1/2" long x 3-5/8" wide. view full answer...
I spoke with the manufacturer, Rhino-Rack, and they stated that the rubber on the Rhino-Rack Fishing Rod Carrier - Locking - 5 Fishing Rods Item # RR573F will squeeze down to fit a max of 1" diameter tube. view full answer...
I have a great solution for your cooler basket fishing rod holder. It is the Replacement Shank for Gen-Y Adjustable Ball Mount item # 325-GH-503 for 5" of height or item # 325-GH-304 for 7-1/2". These ball mounts attach to any 2" receiver and will give you multiple height adjustment options. view full answer...
The face plate of the Boat Buckle Concealed Mounting Kit for RodBuckle Retractable Fishing Rod Tie-Down Strap # IMF14202 you were looking at measures 3" long x 13/16" tall. If this matches the opening on your boat this would be a fantastic option to keep your fishing rods secure while on the water.
I included a diagram of the # IMF14202 for you to take a look at. view full answer...
The concealed face plate dimensions for the RodBuckle Retractable Fishing Rod Tie-Down Strap with Concealed Mounting Kit # IMF14200-02 are 3" W x .85" T, according to the manufacturer. view full answer...
All of the metal surfaces of the Rhino-Rack Ski and Fishing Rod Carrier # RR572 are powdercoated and not painted which like you mentioned does hold up considerably better than paint. view full answer...
Good question, and the threaded rod is 1/2 inch diameter for the propane tank mounting kit you asked about:
- Complete Propane Tank Holder Mounting Kit for 20 lb Tanks # 37220BL
This 1/2 inch diameter rod is also 17-1/2 inches in length. view full answer...
In regards to the Rhino-Rack Fishing Rod Carrier part # RR576F, the 3-5/8" refers to the clearance for bindings like on snowbards which the carrier can also be used for. In other words, it will be the distance from the center of the carrier where the accessories sit to the top of the crossbar. The actual height of the until will be around 6". view full answer...
Yes, they will. The Rhino-Rack Ski and Fishing Rod Carrier item # RR572 will work with Haul Master Crossbars. Those crossbars measure 2.88" wide and the Rhino-Rack carrier fits crossbars up to 3-1/2" wide. view full answer...
I sure can!
With the lid opened as far as it can go, the Yakimia TopWater Rooftop Fishing Rod Carrier # Y04088 measures just short of 12" at its tallest spot. So you're looking at adding about 3" from the carrier's height when closed (9"). view full answer...
The Rubber Fishing Rod and Kayak Paddle Mounts # ER37VR will hold an oar up to 1" x 1-1/2"(see image). I do not recommend trying to fit anything larger than this as the rubber on the end of the strap is not very thick since they cut out the section for it to latch on the other portion of the strap. view full answer...
Yes, to carry your 2 kayaks you will need to add 2 of the Bunk Kit for Malone Trailers # MPG561 to the Malone 2 Tier LowBed MicroSport Trailer # MPG464-LBT. The bottom cross bars are 78" long and are the widest points for the trailer. From the center upright out you will have roughly 38" of crossbar if you choose to mount them perfectly centered on the trailer. This would have your 41" kayak sticking out approximately 3" past the edge of the bottom cross bar which is acceptable. Your Kayak... view full answer...
The Rhino-Rack Ski and Fishing Rod Carrier # RR572 can mount to roof rack crossbars in two ways, with the included universal-fit clamps that let it attach to almost any type of roof rack bar, and also with the T-Bolt hardware that slides into the C-channel slot is on the top of many types of crossbar.
I went to our warehouse and measured the T-bolt in this carrier and the head measures 3/4 x 3/4-inches. view full answer...
The Complete Propane Tank Holder Mounting Kit for 20-lb Tanks, # 37220BL is intended for tanks that have a diameter of 12-1/2" and 18" tall. A 30 lb. propane bottle is the same diameter but is taller, so the rod for the top piece of the hold down clamp is too short for use on a 30 lb. bottles height.
The weight of an empty 20 lb. tank is about 17 lbs. or 37 lbs. when full with 30 lb. tank full, it will weigh about 55 lbs. The Tank Holder, # 37220BL, is built for this weight of 2 each... view full answer...
The width and height of the BoatBuckle Vertical Rod Hold-Down PLUS System # IMF15435 are both approximately 2" while the length is 11-1/2". view full answer...
In regards to the Stromberg Carlson Extend-A-Shower Shower Curtain Rod for RVs, the 35" to 42" versions like part # EXT-3542S has two side pieces which measure around 9-1/2" long and a center piece which measures around 19-1/2" long. The 54" to 60" versions like part # EXT-5460C has two side pieces which measures around 12-1/2" long and a center piece which measures around 34-1/2" long.
I have attached a photo and a list of color options for you as well. view full answer...
Go To Results