The only trailer hitch options for a 2023 Hyundai Venue are class I, 1-1/4" like the Curt Trailer Hitch Receiver part # C57CR which is what I recommend. That said, you can convert this to a 2" hitch using an adapter like the Trailer Hitch Receiver Adapter part # e43YR or part # e93YR. Please note, using said adapter will reduce the hitch capacity by 50%.
Unfortunately, the Hyundai Venue is a subcompact so they don't make the larger hitch size for this as the vehicle can't benefit from... view full answer...
Hey Ralph, we haven't had the chance to install the Curt trailer wiring harness part # C89CR on a Hyundai Venue like your 24' so we don't have an install video yet but in meantime I attached a link to the install instructions which are very detailed and will walk you through the entire process. view full answer...
Hey Ronald, for your 2025 Hyundai Venue we only have 1-1/4 inch hitches available like the # C57CR since it's a lighter duty vehicle. Typically it's only the larger vehicles like trucks and SUVs that have 2 inch hitches available. I know you already have a bike rack and don't want to use an adapter but maybe now would be a good time to have a bike rack that fits this hitch size like the Hollywood Racks # HR200Z? view full answer...
Hey Joe, sorry to hear about the issues you're running into!
The Curt # C89CR you installed on your '22 Venue is rated for 3amps for the right turn and brake, and 3 amps for the left turn and brake, along with 6 amps for the running light circuit. Based on the LED you mentioned you installed, you're no where near having too much load for your vehicle wiring.
Did you ground each light directly to the frame? The issue you are describing is a classic ground issue. I'd double check that each... view full answer...
Yes, we have the Draw-Tite Trailer Hitch Receiver # DT24MR which I recommend for your 2024 Hyundai Venue. This is custom fit so you will not need to drill or weld any components of your receiver to your Venue.
I do recommend installing the Curt T-Connector Vehicle Wiring Harness # C89CR when you install the receiver. This will give you a 4-way flat that you will need should you decide to pull a small trailer or add Auxiliary Lights # C53201. view full answer...
The number ( 411 D) you provided doesn't correspond with a Fan-Tastic Vent roof vent model number, but if yours uses the remote control # FV9068-09 that you referenced, that tells us it's a 7350 Series Fan-Tastic Vent Roof Vent, like # FV807350.
The only way to get the replacement circuit board for your 7350 Series Fan-Tastic Vent Roof Vent is through part # FV807359, which is essentially all the main internal components, including the circuit board, screen assembly, powered lift, as well... view full answer...
We offer 2 different Rack 'Em grass catchers for Exmark mowers. The catcher you need will depend on if the discharge chute is 4 or 5 inches tall.
If it's 4 inches, you'd need # RCMMS4-EXS1 or if it's 5 inches, use # RCMMS4-EXS15.
Each catcher weighs right about 30 lbs. view full answer...
In the attached install instructions for the Curt hitch part # C57CR that you referenced a list of the needed tools is listed and you'll need a ratchet, torque wrench, 3/4 inch drive socket, slot screwdriver, 12 mm socket, and 13 mm socket. view full answer...
If you're going to use the Timbren Axle-less Suspension System 5200-lbs with brake flanges installed, like the 2" lift model # TASR5200S05 or 4" lift # TASR5200S03 , those are compatible with the Trailer Hub and Drum Assembly - 5.2K and 6K E-Z Lube Axles - 12" - 6 on 5-1/2 - Pre-Greased # AKHD-655-6-EZ-K since they have compatible inner/outer bearings, races and grease seals. However, the # AKHD-655-6-EZ-K are not compatible with the Timbren Axle-less Suspension # ASR5200S01 because the... view full answer...
You'e in luck as there is a trailer hitch receiver that is a fit for a 2020 Hyundai Venue, which is the following:
- Curt Trailer Hitch Receiver # C57CR
This is a Class I hitch with a 1-1/4 inch receiver, and is a complete bolt-on installation with no drilling needed. It also has a really nice concealed look, as you can see from the accompanying photo, so your '20 Venue will maintain it's aesthetic. I have added a link to the installation instructions for you to check out as well.
If... view full answer...
Your current 5.30-12 tires fit the same size wheel as a 125/80-12 tire so this is a fine replacement. They both fit a 4 inch wide wheel and you're actually going down in diameter by about a 1/2 inch and the width is basically the same so there won't be any issues with clearance.
A good tire to use as a replaecment is part # AM10130 which is a load range D with a max capacity of 1,220 pounds at 65 psi.
I don't know what bolt pattern your wheels are or what they look like but optoins for... view full answer...
Yes, there is a hitch available for a 2023 Hyundai Venue. It is the Curt Trailer Hitch item # C57CR. This hitch is custom fit and bolts to your Hyundai with included hardware.
The Curt Trailer Hitch item # C57CR is a class I hitch with a 1-1/4" receiver. It is made in the USA and weighs 29 lbs. This hitch has a 2,000 lbs towing capacity and a 200 lbs maximum tongue weight.
If you plan on towing you will also need the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258... view full answer...
The length of the lock cylinder part # LC213116 measured from under the threaded part to the very bottom is 1-3/8 inches. The diameter is 3/4 inch. view full answer...
Unless your state requires a 9AH battery you actually only need a 5AH battery for a HydraStar EOH actuator. For example, the HydraStar # HBA16 which is rated for disc brakes is compatible with a 5AH breakaway battery kit.
Since you need a breakaway battery kit that is compatible with up to a triple axle trailer I recommend the Tekonsha # 50-85-313 because it has a built-in charger, is a top load so it's easy to read, comes with a test button, and is DOT compliant. I have attached an installation... view full answer...
So the biggest benefit of aero crossbars on roof racks is that they are quieter, which leads to a more pleasant driving experience if you are going to leave the roof rack on your 2020 Hyundai Venue (and pretty much everybody does leave their roof racks on their vehicles year-round).
The square and aero Thule crossbars will be able to mount essentially all the same things, but because they are quieter, I do highly recommend the aerodynamic Thule WingBar crossbars. The square crossbars... view full answer...
Both the Draw Tite # DT24MR and the Curt # C57CR are great hitches for your 2022 Hyundai Venue but the better option is the Curt as it does not require fascia trimming like the Draw Tite does. Aside from that you wouldn't notice much of a difference between install or use of either. view full answer...
For your 2021 Hyundai Venue I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C57CR which is confirmed to fit your vehicle, and will not require any drilling or trimming to the fascia of your vehicle.
The # C57CR is made right here in the USA so you know it is a quality product, and in our experience the powder coat finish on the Curt hitches are the most durable keeping the hitch looking great for years to come.
If you can tell me what you are planning on... view full answer...
Yes. The Replacement Converter Section # PD4060CSV is compatible with your existing Progressive Dynamics Inteli-Power 4000 series Power Control Center- this is a 60 amp converter so it is the exact replacement part you're looking for. I've also linked a review video that you may find helpful. view full answer...
The trailer hitch I recommend for your 2022 Hyundai Venue is the Curt Trailer Hitch Receiver # C57CR, which is a Class I hitch with a 1-1/4" receiver and a thicker powder coat than the other hitch options for your vehicle. If you already have a bike rack and cargo carrier system then it's likely for a 2" receiver and their aren't any custom 2" receivers available for your vehicle so you'd have to have one fabricated.
If you don't already have a cargo carrier/bike rack setup, then I recommend... view full answer...
To determine the correct replacement awning roller tube and fabric assembly that you need, measure the distance between the support arms on your Solera awning. Be sure to measure from the center of one arm to the center of the other (see photo).
For example, if the distance between your support arm centers is approximately 20 feet, then the Solera 20' RV Awning Roller and Fabric, with a standard 96 inch projection, will work. It is available in the following color options:
White Fade... view full answer...
Go To Results