I do still have a few options for lifting the trailer but the Correct Track Trailer Alignment and Lift Kit part # RR23QX is indeed incompatible with the MORryde CRE3000 Equalizers. Therefore, you can either change these out to standard ones like the Curved Equalizer for 1-3/4" Wide Double-Eye Springs part # TREQE1 or look into an axle over conversion kit. That said, this option only works for you if the leaf springs are under the axle. If so, I recommend the Dexter Trailer Springs Over-Under... view full answer...
The length I'm seeing for your 2019 Grand Design Reflection 150 Series 290BH Fifth Wheel Trailer is 34' 1" so I recommend the Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer # AD59ZR.
The Olefin HD travel trailer cover works best for long-term storage in all climates. The top panel constructed of Olefin HD fabric blocks harmful UV rays that can cause cracking and fading, beads water on contact, prevents dirt and dust particles from reaching trailer surface, and eliminates... view full answer...
If your trailer is so nose high that you can't use a Roadmaster Comfort Ride Suspension system then you shouldn't be towing it as it is currently. There are multiple ways to fix your ride height issue:
Start by adjusting the hitch head height down, while still maintaining a 6" space between the nose of the trailer and the top of the truck bedrails. If this isn't an option then you can look into alternative hitches that have a lower height setting. If you want me to look for some I'd just... view full answer...
I can help you determine the right replacement double-eye leaf springs for your 2019 Grand Design Reflection 230RL, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as all you need to do is measure your current leaf springs from center-to-center of the spring eyes.
Leaf springs also flatten a bit over time, so you should go with ones that measure a bit shorter than what you currently have. For example, if your leaf springs measured 26-1/4" go... view full answer...
We do have a bearing kit that includes the correct bearings and races for the Dexter 031-030-02 and 031-032-02 bearings, as well as the 010-036-00 grease seal. The correct kit is the following:
- Bearing Kit # BK3-300 view full answer...
Manufacturers don't list the pin boxes they use so I don't know what your current pin box bolt pattern is in order to confirm the fitment of the MORryde Cushioned 5th Wheel Pin Box for 11.5K to 14K Trailers w/ Lippert 1621HD # MR74VR. On your pin box there should be a sticker that has a serial number and RPO number that we can use to determine the bolt pattern, otherwise you'll want to check out the help article I have attached below for step by step instructions on how to measure and determine... view full answer...
The 6169 number you provided comes back to the Replacement Head for Demco Recon # DM6169. With the picture you provided, it looks like you have the Demco Recon 5th Wheel Trailer Hitch # DM8550043.
The wedge that you would need to use with your Lippert Turning Point is the 5th Airborne Custom Wedge # SWW-05. While the # SWW-05 wedge does not specifically list the Turning Point, we have had customers in the past let us know that this was a fit for their Recon and Turning Point. view full answer...
Your 2023 Grand Design Reflection 298BH has 3" axles that are either 5,200 lbs or 6,000 lbs capacity. The correct suspension system for it will be the Roadmaster Comfort Ride Leaf Spring Suspension Kit item # RM-2460-2570 you were looking at. This system is rated for 5,200 lbs to 7,000 lbs axles.
Sorry to disappoint but the only time this system raises the height of a trailer is when it is installed on a trailer with worn out old suspension components.
I have linked an installation video... view full answer...
We don't have any way of knowing what leaf springs are on a 2021 Grand Design 260RD, but I can tell you how to find the right ones. It's pretty easy though, as all you need to do is measure your current leaf springs from center-to-center of the spring eyes.
Leaf springs also flatten a bit over time, so you should go with ones that measure a bit shorter than what you currently have. For example, if they measured 25-1/2" go with the 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles -... view full answer...
Since it's just the Furrion RV Cooktop # FGH4ZSASS that's having the issue it's most likely the built in regulator that's faulty. You can replace the inlet/regulator for this unit with part # FR97PR. If you were having issues with other appliances then that would indicate an issue with the regulator for the entire propane system of the trailer. view full answer...
The Go Power Solar System # 34282729 is compatible with pre-wired Furrion ports for more reasons beyond pin connections.
The Furrion solar port on your 2020 Grand Design Reflection uses their own special two pin port. They also usually have a fuse limiting the port to 10A so I don't recommend using a panel exceeding 120W. You can double-check this on the Furrion's positive wire connected to the battery. Also, because of this direct wire, its best to use a solar panel with a solar controller... view full answer...
Congrats on the new camper! For an extra Dexter 8-201 hub you will want the Dexter Trailer Hub and Drum Assembly item # 8-201-9UC3-EZ. These are sold individually but can be used on either side.
For a spare set of Nev-r-adjust brake assemblies you'll want the Dexter Nev-R-Adjust Electric Trailer Brake Kit item # 23-458-459. This is a left and right hand set so you'll be covered if something happens to either side. view full answer...
I do see that the Lippert Ground Control # LC358590 leveling system was an option on the 2019 Grand Design Reflection 150 295RL 5th wheel camper so you will not have any fit issues with the leveling system.
There are some campers that are unable to use a leveling system due to components underneath the trailer but you will not have that on your Reflection.
The SnapPad XTRA Jack Pads # SP54FR4 will secure themselves to the jack giving you a larger 11" pad. This saves you from having to... view full answer...
For your 2020 Grand Design Reflection 150 Series 240RL with 4400 lb axles the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles Item # RM-2460-2570 is not compatible. I recommend Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 3,500-lb Axle Item # RM-2450.
As far as a disc brake kit. There would be no way for me to know what modifications have been done to the axles. The Titan Disc Brake Kit and BrakeRite Electric-Hydraulic... view full answer...
With the suspension on your 2020 Grand Design Reflection 268BH you would have to weld in some spacers between your current hangers and your frame to get a lift. The Lippert Components Standard Axle Lift Kit you found is only for use on a single axle trailer. We would normally use the Correct Track Trailer Alignment and Lift Kit # RR23QX for a tandem axle trailer but the unique shape of your hangers makes this impossible to accomplish. view full answer...
I reached out to my contact at MORryde and she confirmed that while the MORryde Rubber Suspension Upgrade for Tandem Axle Trailers - 35" Wheelbase - 5.2K to 7K # MR47ZR you were looking at mentions 5200-7000lb axles, it will work with axles as light as 3500lbs, and will work fine with your 5100lb axles as long as your trailer has 35" axle spacing.
To determine your axle spacing for your 2020 Grand Design Reflection 295 RL you will want to measure from the center of the front axle to the... view full answer...
The foot pad of the Replacement 22-1/2" Right Rear Leg for Lippert Ground Control 3.0 Electric Leveling System # LC428493 is welded to inner tube to jack to help shorter the total height for more clearance. The original model has the inner tube a bit longer to allow for room for a pin and clip. Unfortunately there currently isn't a shorter model with a pin & clip design.
In the attached video below Dave will go over this starting at the 2:20 minute mark. view full answer...
For the best results I recommend going with all-new LED assemblies for your Grand Design Reflection 5th wheel. While replacement bulbs are an option, you are better off going with a new assembly made specifically to optimize LED lights. Additionally, the LEDs on new assemblies have a lifetime warranty while replacement bulbs have just a 1-year warranty.
In terms of brightness levels, brake lights on all vehicles are going to be the brightest because they alert the motorist behind them... view full answer...
Yes, your 2018 Grand Design Reflection 220RK can absolutely handle MORryde's suspension system like the MORryde Rubber Suspension Upgrade for Triple Axle Trailer # MR77ZR. view full answer...
Go To Results