See what our Experts say about this Fulton Trailer Fenders

• Mounting Bracket Recommendation for Use with Fulton Trailer Fender # F008563
  The brackets we recommend for use with the Fulton trailer fenders part # F008563 are the CE Smith brackets # CE26098G-2.I attached a picture that shows how these brackets normally hold fenders on. Essentially you put the L up into the top of the inside of the fender on the side that attaches to the trailer and then you attach it to the trailer accordingly.
  view full answer...
  
• How to Mount a Fulton Plastic Trailer Fender to a Trailer
  You can use the hardware and mounting brackets from your original fenders, or I recommend L-shaped brackets, like part # PF775-BKT-2, to mount the fender to your trailers frame. I have attached a link to our product page of mounting brackets we have for trailer fenders. I recommend the L brackets. The one end would be up underneath and the other end would attach to the trailer frame through that skirt. I will include a picture that should better illustrate this.
  view full answer...
  
• Recommended Trailer Fender for 2012 Little Guy Joey Trailer
  The Fulton Single Axle Trailer Fender with Top Step # F008563 referenced in your question does have extremely similar dimensions to the current fender on your Little Guy Joey Trailer. The fender measures 29-1/4 inches long, 9 inches wide, and 12 inches tall so it should work great as a replacement around your 13 inch tires. Customers usually use existing mounting brackets to install the new fenders but in your case I recommend adding some L-shaped brackets like # PF775-BKT-2. One end of...
  view full answer...
  
• Replacement Plastic Trailer Fender for a Venture Boat Trailer
  The Fulton plastic fenders like # F008543 are considered more universal than direct replacements though some trailers come equipped with them. So you will need to go by the measurements on the product page which you have mentioned and re-use the mounting hardware from the old fender. This same style and size is also available in black, # F008553, and silver, # F008563.
  view full answer...
• Replacement Fenders for 1988 17 foot long Escort Boat Trailer
  Since we don't carry a fender that exactly matches the dimensions of your existing fender, replacing both fenders would be your best bet. We do have some steel, aluminum and plastic fenders that are pretty close in size, even though they're not an exact match. CE Smith offers a pre-galvanized fender, part # CE17800G that is 27-3/8 inches long by 8 inches wide by 11 inches tall. They also offer a fender in aluminum diamond plate, part # CE17960ATB which measures 28 inches long by 9 inches...
  view full answer...
• Gray Trailer Fender for 13 inch Diameter Trailer Wheel
  Since you said right front that to me sounds like you aren't looking for a tandem axle fender setup and instead are wanting a fender like the Fulton part # F0085563 which is a silver plastic trailer fender for 13 inch wheels like you are looking for.
  view full answer...
• What Is Width Of Fulton Plastic Fender, # F008563, And Is Mounting Hardware Included
  The width of the fender at the top and bottom is 9 inches and the width of just the step is 7.7 inches. The Fulton Plastic Fender with Top Step, # F008563, does not come with mounting hardware. Fulton does not provide mounting bracket kits for the fenders. You can use your fenders original mounting brackets or use L-shaped brackets from a local hardware store to mount the fender to your trailers frame. I am sending a link to a page of the mounting brackets we have for trailer fenders.
  view full answer...
• Is the Fulton Single Axle Fender with Top Step Compatible with Pre-Existing Fixed Brackets?
  The Fulton Single Axle Trailer Fender with Top Step - Silver Plastic - 13" Wheels - Qty 1 # F008563 can absolutely be drilled to fit the pre-existing fixed brackets on your trailer frame. The capacity of the Polyethylene step will impact the 300 lb rated capacity it was originally tested for.
  view full answer...
• Can Fulton Single Axle Trailer Fender with Top Step be Used for Both Left and Right Sides
  The Fulton Single Axle Trailer Fender with Top Step - Black # F008554 or Silver # F008564 for 14 inch wheels, or Black # F008553, Silver # F008563, or White # F008543 for 13 inch wheels are symmetrical so they can be used on either side of the trailer. Check out the pictures that some customers sent in where they used the same fender for both sides.
  view full answer...
• Mounting Hardware Recommendation For Fulton Trailer Fender
  The Fulton Single Axle Trailer Fender, part # F008563, does not come with mounting hardware included. You can use the hardware and mounting brackets from your original fenders, or use L-shaped brackets, like part # PF775-BKT-2, to mount the fender to your trailers frame. I have attached a link to our product page of mounting brackets we have for trailer fenders.
  view full answer...
• Choosing Fenders for a Small Sailboat Trailer
  The fenders we carry are arranged by wheel size. Fender # F008563 is good for 13 inch wheels. I would need to know the tire size to make the best recommendation. Attaching the fender to the eyelet might be difficult but you would need to use an L-bracket such as # CE26061G-2 and attach it to the same mounting point as the eyelet and then to the fender. I have included a link to our fender main page to the right so you can browse based on wheel size. The measurements are provided on each...
  view full answer...
• Looking for Black Plastic or Steel Fender for 13 Inch Wheel
  We have a couple of fenders that would work for you, but they're just a little bit wider than the spec you mentioned (which shouldn't cause any problems.) The Fulton # F008553 is a black polyethylene fender that measures 9 inches wide, 29-1/4 inches long and 12 inches tall. This is a about 1 inch longer and wider than your existing fender. The closest match is the CE Smith pre-galvanized fender, part # CE17800G which measures 27-3/8 inches long by 8 inches wide by 11 inches tall. I've...
  view full answer...
• How to Mount Fulton Single Axle Trailer Fender
  Yes. You can use the hardware and mounting brackets from your original fenders, or an L-shaped bracket like part # PF775-BKT-2, to mount the Fulton # F008563 fender to your trailers frame. This is a universal fit type of part so you can mount it any way that you see fit, but you will likely need to drill some holes in the fender to match up with your mounting method.
  view full answer...
• Fenders for a 1999 Triton Utility Trailer with 9 Inch Wide 8 Inch Wheels
  Given the width of your tires if you want the whole tire width covered the best option is # F008563. It is 9 inches wide bu 29 inches long. You can mount the fenders by bolting them on but I recommend placing the bolt through a support plate or large washers and then through the fender to the trailer so that more surface area is secured. Or use brackets # PF775-BKT-2, one set for each fender.
  view full answer...
• Is Timbren Axle-Less System A20RS545 Compatible With 13 Inch Loadstar Wheel and Tire
  Definitely a smart idea to check for compatibility, and I can confirm for you that the Timbren Axle-Less system and Castle Rock tire and wheel you asked about will absolutely work together. The parts are the following: - Timbren Axle-Less Trailer Suspension System with Hubs # A20RS545 - Loadstar ST185/80D13 Bias Trailer Tire with 13" Galvanized Wheel # AM3S334 The Timbren system uses hubs that have a 5 on 4-1/2" bolt pattern, and are compatible with wheels up to 13", which is the same...
  view full answer...