To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you need to carry taller or longer gear, the Lomax Professional Series makes it easy. The tri-fold aluminum panels fold up quickly to open two-thirds of the bed, and integrated storage clips with retractable straps keep the folded panels secured while you drive. When you need even more space, the panels lift off entirely without tools, so you get full bed access in seconds without any extra hardware or adjustments.




This cover uses impact-resistant aluminum panels that are 20 percent stronger than aluminum truck body parts. Even though they’re tough enough to withstand hail or falling debris, the whole cover weighs only about 50 lbs. The black diamond mist finish resists scratches, UV damage, and daily wear while giving the bed a sharp, finished look. It supports up to 400 lbs of evenly distributed weight, making it both rugged and easy to handle.

Keeping cargo safe matters, and the Lomax Professional Series locks down tight. The tri-fold panels automatically latch to the side rails at 10 points when closed—2 hooks at the front, 4 along the channels, and 4 more latches that engage as you fold it down. With no exterior latches to pry open and a locked tailgate, the bed is completely secured against theft or tampering.
Rain, dust, and snow stay out thanks to continuous watertight rubber seals along the side rails and waterproof, vinyl-coated hinges. The cover’s subtle arc directs water off the surface instead of pooling, so it sheds moisture naturally without using drain tubes. The result is a clean, dry bed through storms and car washes alike.

Sitting only about 1/2" above the bed rails, the low-profile design blends smoothly with the truck’s lines. This sleek shape not only looks clean but also cuts down on wind noise and drag, helping improve fuel efficiency. It mounts inside the bed rails, leaving stake pockets open for racks and gear when you need to haul more.




Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everyone, Collin here at eTrailer and today we're going to take a look at Lomax' line of professional series hard tonneau covers. This going to be folding style tonneau cover. It's going to be very strong and durable and protect your truck bed and the cargo in the inside from the elements. Now these covers are going to have a nice diamond plate design to the top of them. It's going to give just a pretty nice rugged look to the cover and add to the style of your vehicle. It's also going to go hide scratches, dents and dings very well.
A lot better than some of covers out there. Not only is this cover going to protect your truck bed from the elements, but it's also going to add to the looks to your truck. You don't see a lot of these diamond plated aluminum covers like this.It's just a nice change of pace from those matte black or glossy black finishes that you see on a lot of other tonneau covers. The cover's gonna have rubberized weatherstripping all along the perimeter and that's just going to help keep out water and other debris. Now unlike a lot of other covers.
This one's going to have in bed side rails, meaning we're not taking up any space on the top of our truck bed side rails, so we still have full access to our stake pockets should we need them. Now because the cover does not open from the outside and you have to open the tailgate to do it, if you have a locking tailgate your going to get great bed security. Nobody will be able to access the cover at any point. To access your cover all you got to do is open up your tailgate and then locate the cord on the underside of your cover. And then you simply just fold back each section.With the cover in this position, we have partial bed access and we can actually travel with it like this by securing our strap right here to make sure it cannot go anywhere.
And we're actually going to have this brace without a nice soft rubber pad on the bottom. That's going to help protect that cover from damaging itself. We're going to have one right there. We're also going to have one towards the back right here and two more on the other side. Now there's going to be 10 different points that are holding our cover in place when it's fully closed and how they actually work is this peg right here is going to sit under this tab.
So you do want to be mindful of when closing the cover to make sure that you engage this peg under the tab and it doesn't get caught sitting on top of it.Now even though the cover is latched in this position. Should those fail at all, we do have these safety carabiners attached to it to make sure the cover stays attached to the rails. Our support braces on the underside of the cover are going to make sure that our cover is very durable. It's going to be able to support 500 pounds of evenly distributed weight, but they're also gonna double as handles to help close and open your cover. Now, like I said, we have in bed side rails, so we're not taking up any space on the top of our side rail caps, but we are going to be sitting in about two inches on the inside of our truck bed. So that's not going to be taking up too much space if you do decide to travel with your side rails on while the cover's removed. The cover's going to have a nice low profile design to it.It only sits about a half inch above our truck bed. We're also going to have this nice rubber strip on the back of the rear panel right here, so when you open up this first panel it's going to elevate a little bit off of that middle panel to make sure that it doesn't sit flat on top of it. We also have a weather seal on the back side of our side rails that are pressed up against the side of our truck bed side rails, which is also going to help keep water out. There's also going to be a weather seal on the back where the tailgate shuts, so when we close our tailgate it's going to activate and sit on top of our tailgate. The side rails are held in place by a series of these aluminum clamps which clamp down on the upper part of the inside of our tonneau cover side rail and on the back side of our truck bed side rail. You do want to make sure that you're clamping these down onto the metal frame of your side rails on the truck bed, not just the plastic caps.Now even though we only have partial bed access with the cover forward in this position we can gain full bed access by moving the cover completely, which is pretty easy to do. All we have to do is remove the safety carabiners and we need to locate this trap that's on the underside of the cover right there. Once we pull that down, we can lift up slightly on that part of the cover and then it just slides right out of it's slot. You can do this by herself if you're standing in the truck bed like I am and it's very easy just to grab and remove. When putting it back in place the easiest way to do that is just to stand it up like so. Just make sure you get your pegs to line up. We're just going to scoot it up all the way to the bulkhead and then lay it down and push it in place. Once we have it pushed in place, just latch it down. Now that's going to do it for our look at Lomax's line of professional series hard tonneau covers.
Ratings & Reviews

Dan
4/4/2023
Awesome! Keeps things in the bed dry and safe. It’s sturdy, quiet and efficient to open and close. If I have something taller than the bed walls, it folds up easily into a compact size so it can be easily stored in the bed, and put back in when cargo is removed
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.






Kate F.
3/18/2026
Thanks for including the picture Andy, the cover looks sharp on your red truck! Thanks for being a loyal etrailer neighbor (customer).