Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Double-eye leaf spring acts as part of a trailer's suspension system by providing an attachment point for a 2,500-lb axle. Spring flexes to resist shock and also ensures a smooth ride. Includes bushings with 9/16" inner diameter.
Features:
Specs:
| Part Number | A | B | C | D |
|---|---|---|---|---|
| 072-006-00 | 12" | - | 23-1/8" | 3-5/8" |
Note: To ensure proper axle alignment and suspension performance, leaf springs should always be replaced in pairs.
Leaf springs are an integral part of your trailer suspension system. The leaf springs provide the attachment points for your trailer's axle, suspending it from the frame of your trailer. Each spring flexes to absorb road shock as you travel, allowing the axle to move somewhat independently of the rest of your trailer. This helps to reduce wear and tear on the trailer and also ensures a smooth ride.
Double-eye leaf springs attach to hangers that are welded onto your trailer. One end of this spring will attach directly to the hanger with a suspension bolt. The other end will attach to shackle straps that are suspended from a hanger. These straps allow the spring to move and pivot so that it can better compensate for uneven pavement. If you have a tandem- or triple-axle trailer, the shackle straps will be attached to the equalizer that connects multiple springs.
To mount this spring, you will need hangers, shackle straps, and suspension bolts. If you are simply replacing a spring, you may still have hangers welded onto your trailer. You should, however, replace your shackle straps because they are usually the first component to wear out. You may choose to replace old suspension bolts as well. It is recommended that you replace the other leaf spring in your setup at the same time. Because springs can sag and elongate as they wear, this new spring may not exactly match the old one, and the alignment of your trailer could be affected.
If you are fabricating a trailer, you will need to purchase a hanger kit for installation. To determine the type of hanger kit that you need, you must know the specific type of leaf spring that you have, as well as your axle capacity. Depending on the hanger kits used with them, springs can be configured to work for single-, tandem- or triple-axle applications. Hangers and other suspension components can also be purchased separately if there isn't a complete kit that works for your setup.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody, this is Jeff atetrailer.com. Today we're gonna take a look at the Dexter 23 1/8 inch long three leaf double eye spring for 2,500 pound trailer axles. Now this leaf spring will act as part of your trailer suspension system, provides the attachment point for your trailer's axle. Now these are multiple leaves to allow flexibility to absorb road shock. This spring here has three leaves and it allows for a nice smooth ride, reduces wear and tear on your trailer, and ensures a level right on bumpy and uneven surfaces. Now the length of this is always measured from the center of one spring eye to the center of the other when it's unloaded like it is now.
So if we get our tape measure and go center to center, measure your 23 1/8 inch measurement. The width of the spring is 1 3/4 inches. This is a sturdy steel construction. If you notice the nylon bushings are installed and included, and the eye diameter when the bushing's installed measures 9/16 of an inch. Now the prem mounted hangers are the aftermarket hangar kit, which is required for installation.
Those items we do sell separate on our website. Basically this spring will attach to a hanger mounted on your trailer frame at one end, and then the other end connects to shackle straps suspended from a hanger or equalizer. This is for a quantity of one leaf spring. Spring capacity is 1,250 pounds. So when this is matched with one on the other side of the axle, it'll meet the 2,500 pound axle capacity.
Now there are additional dimensions on the spring if you need them, they are listed on the product page. But that should do it for a look at the Dexter 23 1/8 inch long three leaf double eye spring for the 2,500 pound trailer axles.
Customer Satisfaction Score:
87% were satisfied with this product
13% of customers were not satisfied
Ratings & Reviews
Brooke M.
6/4/2025
I totally get wanting to buy USA-made, but Dexter is still a reliable brand. While they are manufactured overseas, the I think you'll find the quality is still there. :)
Kate F.
4/23/2026
I am absolutely shocked to hear this on a Dexter leaf spring. What was the measurement of the one you took of?
Bradley
4/2/2025
Springs are still operating properly.
Brooke M.
3/19/2025
Yeah, that is definitely not a break the spring could bounce back from. So glad we had what you needed to get back up and running again!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Lazer S.
10/14/2025
Install looks great, Christopher! This is an upgrade a lot of people are doing lately and it will be a big improvement from what you originally had installed! Any more trips planned for the year or are you getting everything ready for next season?