Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Square drop leg features adjustment holes, steel construction, and corrosion-resistant zinc plating. Pair with Fulton's 13" long weld-on outer tube to create a stabilizer jack with 3K capacity.
Features:
Specs:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to be taking a look at a Fulton square drop leg. Now, this drop leg is designed to be paired with the weld-on outer tube which would then create a stabilizer jack for your trailer or for your application. Your outer tube is sold separately. It is available here at etrailer.com just like this one right here, part number SJ10300. This would weld on to your trailer frame. You can see how that fits in there.
You've got all the adjustment holes. The bottom hole down here is for the fully retracted position and then you've got all your adjustment holes located on the drop leg itself. A really nice design. Again, you can find this right here at etrailer.com. When this drop leg is paired with this unit right here it's going to have a capacity of 3,000 pounds. Now, on the drop leg, it's a steel construction.
It's going to have a really nice, well done zinc plating. It's going to offer corrosion resistance to the unit. The overall length from the bottom of the foot plate to the very top of the tube measured around 29 inches. The tube itself is a square design and it measures 1-3/4 of an inch by 1-3/4 of an inch. The foot plate measures about 7-1/2 inches by 3-7/8 of an inch.
The foot plate's really nice. It's welded on there. That's going to really help spread out the applied weight especially on softer surfaces. It's going to help prevent sinking. A couple holes in it so if it traps some dirt and moisture, that does have a way to escape off of the foot plate. The distance that we have between this hole right here which is going to be the highest setting and then your lowest setting is right here.
The distance between those two holes on center measured 16 inches. Center-on-center between each hole is 2 inches. That's our incremental height adjustment. The distance between this hole and this hole is 7-1/4. The diameter of each hole is .52 inches which is just slightly larger than 1/2 inch. From the center of the lowest adjustment hole to the bottom of the foot plate is 9 inches. From the center of the highest adjustment hole to the bottom of the foot plate is 25 inches and then again, you've got the incremental height adjustment of 2 inches. From the center of this hole, which again is the fully retracted or stowed position. If you're in travel you want to put it in this position. From the center of this hole to the bottom of the foot plate is about 1-3/4 inches. That's going to do it for today's look at the Fulton square drop leg.
Worked for my pj dump trailer, however I did cut one side of the curled edges to make the bottom hole on leg align with the holes in the trailer. I use it to load my 10k machine. Worked great.
As promised, pictures of the trailer that I have modified using parts from Etrailer.com. Of course these were taken on Valentine's day at the range during a live fire demonstration. The gun bolted down in the trailer is an M3AC .50BMG Aircraft gun that had once been used as a "Belly Gun" in a WWII bomber, the trailer is an M1102 Hum Vee trailer that I modified as a platform to permit the mounting of several different guns. The Drop Down Fulton Jacks imparted enough stabilization to the trailer to not only permit the weapons system to operate safely but also, to permit a Singing Quartet to deliver a Singing Valentine and flowers to our ladies on Valentine's day from inside the trailer. It never wobbled or shook at all. The parts from Etrailer.com proved to be very stout and durable. Should you decide to use any of these please digitally obscure the license plates. Thank you for ensuring prompt delivery of quality parts so that I could facilitate the modifications in time for this event. Respectfully, Frank
Perfect fit. Holding up well to salt exposure. Good range of adjustment. Fair price.
Fits as it should
Perfect for my application, will be installed on my Miller gas welder . Drop down when transporting keeps wheels off trailer floor
etrailer is Awesome!!! Couldn’t find this discontinued part for Fulton Magnum Series jack anywhere, but etrailer had a brand new replacement for it. They have fast shipping and great customer service as well. I recommend everyone to buy from them, you won’t be disappointed.
I like what I ordered. I haven't installed them. Plan on it this week end. I can tell everyone that everything that I have ordered from etrailer has been great. I have been ordering for many years.
Received the stand quickly. Good price and quick shipping, Thank you!
The bottom hole was in the wrong position for the trailer im using it for. Other than that issue everything is great and shipped quick
easily adapted product to my trailer
Product exact match to original part on trailer exactly as described
Not the size advertised. It’s 1.5” not 2”
Sierra K.
10/18/2021
The distance between the adjustment holes are 2 inches. The tube diameter is 1 and 3 quarters all the way around.
They worked exactly how they should, Have a merry Christmas!
Keith
Great product
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Randall
8/14/2022
Good, still working as needed