
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Hauling long lumber but still need bed access and a toolbox in place? This aluminum rack clamps to bed rails and adds a 32" over-cab cantilever, with integrated toolbox mounting so you can carry extended loads and keep your bed usable.
Long material gets sketchy fast when it runs past the front crossbar with nothing supporting the overhang. This rack includes a cantilever extension that attaches to the front crossbar and adds 32" of length over the cab, so lumber, pipe, ladders, and trim get another support point instead of hanging out unsupported. The cantilever crossbar is built in the same style as the main crossbars, so the setup stays consistent across the full load path when you're hauling oversized material.
Permanent drilling slows the job down and leaves you committed to the setup from day one. The T-Rac Pro2 mounts to the truck bed rails with support bases that secure using 2 heavy-duty aluminum clamps per base, so you position the bases where the instructions call for and torque them down for the connection. The included toolbox mounting kit also uses 4 aluminum clamps with pre-drilled center holes and mounting hardware, so you can mount a crossover-style toolbox without drilling into the bed rails.
Odd-shaped cargo gets frustrating when your tie-down points and stops are stuck in one spot. The aluminum crossbars use integrated slots on the top and bottom for mounting and adjusting accessories, and this rack includes 4 load stops and 4 cleats to give you multiple ways to secure what you're carrying. The load stops slide along the crossbars with a quick-release knob, and the cleats mount along the outside of the upright supports, so you can set up bookend-style support for ladders and lumber or add anchor points for cargo riding in the bed.
Daily hauling beats up rack hardware fast, especially when the setup sees weather, road grime, and repeated loading. This system uses durable, lightweight aluminum construction with a dual powder coat finish that includes an electrostatic powder coat and a clear finish for added protection from scuffs and scratches. The rack is rated for up to 1,000 lbs when properly installed and weight is distributed evenly, and the corner brace design with aluminum crossbars keeps rack and cargo stable and secure when the truck is loaded down.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, I'm Matt with etrailer. Today we'll be talking about the Thule TracRac Pro 2 ladder rack. So let's take a closer look at it. Ladder racks in general are just gonna be able to give you the ability to maximize your bed space. And on top of that, if you get one with a cantilever like the one we have today, you'll even be able to get some longer items on here. That's anything like your piping, your lumber, ladders, even kayaks, anything of that nature, it's going to be a really good fit up here.
Another thing I do like about this one in particular is it's gonna be by Thule & Thule. The stuff they make, one, it looks really nice, very sleek back here. And the other thing is it's typically gonna have very smooth touch points. So one of the big touch points on here that I like a lot is gonna be these load stops. So what these load steps do is they prevent your load from shifting on you.
So if I go shake this right now, (rack rattling) it might move a little bit side to side, but it's stopping as soon as it makes contact with that load stop there. You're gonna try to get these in as close as possible and you can adjust them just by turning this hand knob right here, bring it in or out. But if I fully wanna show how far this can go, I'm gonna have to take off my ladder first. So you'll just adjust them by, again, turning the hand knob, bringing it in or out, just like that. And if you ever do wanna completely take it off, there's gonna be this cutout here in the center (metal whooshing) that gets removed just like that.
So super simple to handle. If you do need the full space, maybe you wanna put a type of rooftop tent up here, and you can get that to clamp onto your bars as well. But the way this basically goes on is gonna be via these T channels here at the very top. And another way of securing the gear down other than this, because you're gonna also use these holes here as a hook point, like I was doing earlier with my ratchet straps, you can also tie things off via rope. So we go over here to this cleat, you'll be able to wrap your ropes around here.
I know a lot of other people typically use this spot for a type of point to hang up any type of cable you might have on hand. This I will say is kind of narrow, so I don't think you'll be able to utilize that as easy. Now, we can talk about how far this cantilever is gonna sit on your setup. So going from center bar to center bar, the front two ones, this is gonna be roughly about 32 inches. So as you saw there for my ladder, that did make a big difference. So that ladder isn't dipping down. This is a little bit more calming if you have any type of lumber or piping 'cause that's gonna have a lot more bend to it and you definitely don't want that either making contact with your cab or bending down enough where it's kind of getting in the way of your view in front of your front windshield. I'm gonna give you guys two more measurements so you can apply this to any vehicle out there. So the total height this adds to your vehicle just for the rack itself is gonna be roughly 25 inches. Lets you know if you're gonna make it under a space like a garage, also account for those load stops right there too. And then for underneath here, that's gonna be 23 and a half from right here. So that lets you know how much space you have underneath your bed so you know if you still have room to put anything under there, like a fridge or a washer or dryer. Something though that I like about this is that it's gonna be a no-drill installation and you can still use this with some toolboxes out there. So the way this basically works is we can come right over here. There's gonna be these clamps and they just squeeze the base of this to your bed rail. So using it right now, super easy, no drilling, just squeezes on. Now, if you plan on using a toolbox with this a lot of times, a toolbox installs in a very similar way. And how your toolbox is gonna interact with this is that side that typically rests on your bed rails is gonna rest on these clamps. There's gonna be an adapter to make that feel a little bit nicer and then there'll be a bolt that goes to the very top of it to connect these to the clamps to secure it down. This is also gonna be rated for 1,000 pounds, so that's gonna be quite a bit. But something else to consider is if you're fully loading up your bed and you're trying to put things on top of here, just check what your vehicle's weight rating is so you don't exceed that and damage something. Now, overall, I do think this is gonna be a great option for a lot of people out there, one who are gonna be carrying those longer accessories or items. You want something that looks sleeker and just feels nice to operate, you can't go wrong with this. Of course, you can get this in a variety of different sizes just depending on the size of your truck. And of course if you don't need to carry those super long items, we are gonna have an option of this that's just gonna be the ladder racks themselves. But if you guys have any other questions, let us know here at etrailer. And again, I'm Matt and thanks for watching.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.







Bruce
7/13/2025
The rack is durable and doesn’t make noise from wind at speed.