Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

Video Transcript for Curt T-Connector Vehicle Wiring Harness Installation - 2017 Chrysler 300C

Today on our 2017 Chrysler 300C, we're going to be taking a look at and showing you how to install the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56235. This is what our wire looks like when it's installed. You can see it's going to live inside the vehicle. This is going to provide you the necessary power to light your trailer. You're going to have three amps per circuit for your stop and turn signals. You're going to has six amps per circuit for your tail lights. When you're not in use, you just simply take it, roll it up.

You can store it off to the side, and when you're ready to use it, drape it out the back. Make sure you stay away from the latch. Close your trunk. Now let's show you how to get this installed. To begin our installation, we need to get inside the trunk.

We're going to remove our floor covering here. We're going to remove this sill pan here. We're just going to lift up on it, so now we're going to remove our panels on the side here. First, we're going to take out this hook. We're going to be using a T25 star bit.

We're going to have two fasteners here. We're just going to pull up on them. Here we're going to have another push pin. We're just going to pull out on it. You're going to have some wiring that goes to this light. We're just going to unplug it.

All you're going to do is push it in on it's head to pull it out and take this and pull it around the trunk here. What we're doing, is we want to gain access to this plug here. From here, you want to unplug the taillight. This little red tab we're going to pull out and we're going to push down on that piece. We're going to take the end with our green wire and brown wire. We're going to hook one in into the wire we just off, the other end right into the spot where we removed that wire. Now, we're going to repeat that process on the other side of the vehicle. We went ahead and cleaned our area once we found a good location and we're going to take our two sided sticky tape and take one side, we're going to stick it to our modular box, press it in to place and we're going to take the other side, press it in to place. Make sure you got a good hole. Next, go ahead and put our ground in place, we're going to put it right here on the existing ground that's coming from the battery. We're going to use a 10 millimeter wrench. Go and install your ground and reinstall your nut. From here, we zip tied our yellow wire that's going over to our driver's side along the wire from the factory that's running around the back of the vehicle. It's underneath the sill panel. We're going to go ahead and put our carpeting back in place. You want to make sure that your power wire is coming out the bottom there. Feed that around there. You want to make sure to plug your light back up. Put these fasteners back in. Last we'll put inaudible 00:03:19 back. Now, we're going to repeat the same process on the other side of the vehicle. We're going to connect our positive cable. We're going to do it right here. We're going to be using a 10 millimeter socket. We'll remove the nut, put your ring terminal on, replace your nut, tighten it down. We'll put this cover back on. Once we have all our connections made, we can install our fuse. We can install our sill panel and it'll just pop into place. We can reinstall our floor cover. You want to make sure that your inaudible 00:03:58 holes hanging out. We'll go ahead and test everything out using part number I26 that you can find on our website. Brake lights, left turn, right turn, running lights. That'll do it for the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56235 on our 2017 Chrysler 300C.