# 1
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
The Curt trailer hitch and wiring harness for my 2016 Highlander was a perfect fit. Installation was a breeze just following the etrailer videos. I opted for the 4" drop ball mount because of the Highlanders ground clearance but the standard 2" drop would have been just fine. Will use etrailer again without hesitation.
I purchased this hitch to pull my utility trailer with. It was easy to order, arrived on time, and simple to install/use. This hitch is built very well and strong, and has a good coating finish on it. Great product!
# 2
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
Works perfectly. Fast shipping. Very Satisfied.
# 3
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 4
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 5
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
# 6
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This is a huge difference maker for us. I can open the tailgate of our truck with the trailer still attached, and helps minimize any body damage if my backing up is not good.
# 7
Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
Incorrectly listed on etrailers as a 3-1/8” rise, when really this is a 5-1/8” rise (marked correctly on the item itself, but listed incorrectly on this website).
I am completely satisfied with the product. Great quality and excellent finish. Prompt shipping and excellent customer service. It is stylish and functional and will meet my needs for towing up to 3,500 pounds. I would definitely do business with this company again!!!
# 8
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 9
Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs
Still haven't towed anything with it yet but it seems very solid. I do think it will rattle some in the receiver because it is loose in my 2" receiver on my 2019 F150.
This hitch has worked out great for me over the last year. It’s very heavy duty and easy to adjust. I’ve hauled a 9,000 lb boat, long-distance on numerous occasions without issue. I also haul a landscape trailer on a daily basis weighing over 5,000lbs and haven’t had a single issue. Great hitch that was significantly cheaper than others and is very high quality. I’ve recommended it to several people and I wouldn’t hesitate to buy again. The only thing I would like to have now in a hitch is a tongue weight gauge, but it isn’t necessary.
# 10
Curt Solid 2-Ball Mount for 2" Hitches - 2" and 2-5/16" Balls - 10K - Black
Very solid.. great product !!!
This thing is very solid and heavy duty; it weighs in at 16.8 pounds. I haven't pulled with it yet, but I believe it's exactly what I needed to pull the two trailers I need to pull (2" ball, and 2 5/16" ball).
# 11
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
great product great service I bought the hitch took me 15 minutes to install it on a 2004 civic fast shipping great company thanks
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
# 12
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 13
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 14
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Items packed well delivered on time. Doesn't get much better that that.
The service is great and so is the price. Box came damaged but if it installs as easy as the last one I bought from etrailer I will be very happy!
# 15
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
Solid quality and workmanship.
# 16
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 17
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
Fits my Forester dealer-installed 2 inch receiver perfectly with the pin (purchased separately) in the first hole. The gas tank is in the way so I can't push it in further to the second hole. It is impressively strong, so there is no problem with it extending rearward a bit, but ideally I would get a shorter hitch if I could have a do-over, just for ease of storage.
Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".
# 18
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
# 19
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
etrailer is great! My hitch shipped quickly and was packaged well. Plus customer service has been great keeping me updated and staying in touch with my order.
Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!
# 20
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
What our customers are saying:
"You folks are fast. Thank you very much."